Slurry reeler

Mouser · Apr 25, 2017

Speedstar said:
It is not as simple as that all fitting's and valve's need to be rated at 16 bar pressure,if you want to stay on the right side of the HS laws

Oh ok, scrap that idea then.

Speedstar · Apr 25, 2017

davedb said:
If your only blowing the last few 100m of pipe out the launcher won't have to stand anything like 16bar pressure a hd35 produces that much but as the pipe length increases pressure drops so near the field won't be anything like that, we occasionally just use a T piece with a ordinary tap on it and don't have any trouble

Compressor will make 16 bar of pressure, I would not want to see someone get hurt but a mz gate valve coming apart

Peppa pig · Apr 25, 2017

Somthing like this

davedb · Apr 25, 2017

Speedstar said:
Compressor will make 16 bar of pressure, I would not want to see someone get hurt but a mz gate valve coming apart

We're not using a mz valve to be fair it's a proper tap as used on a lot of pumps but the best valves we have are ex water main wheel valves they are well able for the pressure

Blue. · Apr 25, 2017

davedb said:
We're not using a mz valve to be fair it's a proper tap as used on a lot of pumps but the best valves we have are ex water main wheel valves they are well able for the pressure

Lots available on eBay.

jack6480 · Apr 27, 2017

Peppa pig said:
Somthing like this

Smart!

jack6480 · Apr 27, 2017

Speedstar said:
Wox one is no good as it is to small & can not be ran on the front of the tractor & from what I have heard it is about the 10K mark

Your chatting sheet

Speedstar · Apr 27, 2017

jack6480 said:
Your chatting sheet

What ?

rc mx110 · Apr 28, 2017

jack6480 said:
Your chatting sheet

jack6480 · May 6, 2017

Can someone tell me how anyone gets a doda hd35 or a Bauer sx1000 to pump more than 130 cube an hour at 1200m currently 128 cube 9 bar 890 revs with the Bauer in water doda was similar yesterday

jack6480 · May 6, 2017

600m of 5 inche 600 4 inch

Speedstar · May 6, 2017

jack6480 said:
600m of 5 inche 600 4 inch

Your 4* hose is killing your flow
600 meter's of 4" will kill it by 60 to 100 cube per hour depending on your land and the type of slurry you have

Peppa pig · May 6, 2017

rubbish utter rubbish

Speedstar · May 6, 2017

Peppa pig said:
rubbish utter rubbish

Would you care to say why ?
Have you pumped the same distance with 4" then dropped it off and put the same on in 5" as if you had you would know the answer

mtx.jag · May 6, 2017

jack6480 said:
Can someone tell me how anyone gets a doda hd35 or a Bauer sx1000 to pump more than 130 cube an hour at 1200m currently 128 cube 9 bar 890 revs with the Bauer in water doda was similar yesterday

My opinion is because it's water..

mtx.jag · May 6, 2017

mtx.jag said:
My opinion is because it's water..

We could never get the pressure or volume with dirty water that we could with slurry or dirty water with fiber in on HD35,backing plate tight to impeller as well..

Eminus · May 6, 2017

5" is 78% more than 4"

Peppa pig · May 6, 2017

jack6480 said:
Can someone tell me how anyone gets a doda hd35 or a Bauer sx1000 to pump more than 130 cube an hour at 1200m currently 128 cube 9 bar 890 revs with the Bauer in water doda was similar yesterday

Is it clean water.dirty water.or dairy washing water???

Rob78 · May 6, 2017

Bigger pipe = higher flow rate

Peppa pig · May 6, 2017

Rob78 said:
Bigger pipe = higher flow rate

How was the preassure only 9 bar then.surely it would have been far higher if the 4in was the restriction??assuming the preassure guge is on pump.

Slurry reeler

Member

Member

Member

Attachments

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

0 %

Up to 25%

25-50%

50-75%

75-100%

100% I’ve had enough of farming!

Share this page