Search results

  1. T

    Agco/Topcon agi 4 receiver for sale

    We have recently bought a Massey Tractor which the previous owner ran topcon gps on it. All the wiring, valves etc are still on the tractor they just kept the receiver. so I was wondering if anyone knew of any agco/topcon agi 4 receivers for sale. Iv found a few ones off fendts but they won’t...
  2. T

    MF 7620 Vario engine re map good or bad idea.

    We have got a Massey Ferguson 7620 with a vario transmission, we are considering getting it remap as we are just short of a few hp when towing the drill (non pto drill). I’m wondering if anyone has done it before and if they gained more power or does the transmission just give up under the same...
  3. T

    Case / new Holland big square baler control box problem

    We have changed the tractor we run our case lb423 square baler on to one that has not got iso bus on, so we have had to use the proper case control box. It has always beeped every time it ties knot when we have run it on iso bus, but since we’ve had it running on the correct control box it come...
  4. T

    Lupin whole crop mix seed

    Looking for a lupin whole crop mix for 5ha wondering what was available and price? Or something similar
  5. T

    Lupin and triticale whole crop

    I will apologise in advance because this has probably been discussed on here before I just can’t seem to find it. I was wondering if anyone has grown a Lupin and triticale mix before for whole crop and what there experience were with it and feeding it too fattening cattle. On paper it should...
  6. T

    Tips on how to use a Mzuri in the wet

    Hi, its my second year in strip till and could the two years get any different!! We’ve got a Mzuri pro till and I was wondering if anyone had any tips or experience of how to use them in wet conditions. I am trying to drill into osr stubble and I am struggle to make ours make a reasonable seed...
  7. T

    Opico dryer thoughts

    Hi We are looking at changing from our old batch drying system to an Opico mobile dryer and we have found one local that reasonably priced. I don’t know much about gas dryers because our old one is diesel, and the thought of gas has always put me off because you can’t just go to the red diesel...
  8. T

    Round baler: Kuhn - Vb2190

    Round baler: Kuhn - Vb2190 Category: Round baler Manufacturer: Kuhn Price: £10000 Condition: Used Description: Kuhn vb2190 belt baler this will bale up to 6 ft bales. We bought this baler as an ex demo so it is a high spec baler, second drive roller kit, and soft centre kit. It has only...
  9. T

    Mixed farm looking at going to strip till

    We are a mixed farm with about 300 head of cattle are are looking at going to strip till. The crop rotation is osr, winter wheat, something a second wheat/ winter barley/ then either spring barley then back to osr or winter oats or spring beans, there is also so about 25ac if maize in the...
  10. T

    Wanted spearhead bat wing topper

    im not sure if this is in the right but I looking for a spearhead bat wing rotary topper for under £7000 and I was wondering what people knew there was about. Many thanks
  11. T

    Any wilder grain dryer's for sale?

    i Know this is a bit of a long shot but I was wondering if anyone knew of any Wilder grain dryers for sale anywhere. I know they aren't the most popular with people but we already run one and it suites our system well because they are full automatic. So we were wondering if there were any more...
  12. T

    Pedigree Limousin stock bulls for sale

    We have 6 2 year old pedigree limousin stock bulls for sale, they have good size and shape, also let out into a half acre paddock daily for exercise. We are in a yearly tb testing area and have been clear for 6 years now and they are pre movement test and ready to go to work. Located in...
  13. T

    Whole crop oats

    Has anyone or know of anyone that has done whole crop oats and clamped it? We are short of silage ground this year so we were thinking of putting Spring oats in to whole crop so we can bulk the silage out with them a bit. I want to grow oats as it won't mess up the rotations and it means we can...
  14. T

    What size clamp to build

    Looking at putting a silage clamp in this time instead of bales for our suckler cows. We roughly do about 1000 to 1200 bales a year at the moment but probably would only clamp first and second cut which would roughly be about 400 to 500 tonne of fairly well wilted grass. So I was wondering if...
  15. T

    What trailed foraged harvester to buy

    looking at changing from baled to champ silage this year for our suckler cows, we roughly do between 1000 to 1200 bales a year but we are just getting fed up of the time it takes to do it and then the cost of all the plastic. Iv been looking at a jf 900 but just wondered what people thought? We...
  16. T

    Difference between John Deere 3760 and 3765 trailer foragers

    I am looking about buying a trailer forager for next year to do my own silage I roughly cut about 120 acres first cut and 70/80 second cut for my suckler cows. I have seen some John Deere trailer foragers for sale but I can't seem to find any information about them. I was wondering what the...
  17. T

    Pedigree limousin Bulls for sale

    8 pedigree limousin Bulls for sale aged between 23 & 24 months old, they are well grown and ready to go to work but have never been pushed hard with corn. They are out of well bred easy calving sires and have good shape and are quite. Located near Stafford 5 miles 10 minutes from junction 12 m6...
  18. T

    Pedigree limousin Bulls for sale

    8 pedigree limousin Bulls for sale aged between 23 & 24 months old, they are well grown and ready to go to work but have never been pushed hard with corn. They are out of well bred easy calving sires and have good shape and are quite. Located near Stafford 5 miles 10 minutes from junction 12 m6...
  19. T

    Net replacement film (baletite) applicator kit

    i have been looking around but can't seem to find much about it. I was wondering if anybody know's if you are able to get net replacement film applicator kits to fit on balers that haven't got it on as standard, as I can't seem to find any company's that do them. I'm not sure it is even possible...
  20. T

    Will tanco 1050a wrapper wrap 120/70 quadrants

    I am looking at buying a square bale wrapper to wrap quadrant (120/70) bales? I don't have a huge budget to play with and I have seen a tanco 1050a wrapper and I was wondering if any one knew if they would wrap quadrants as I can only seem to find pictures of them wrapping 70/80's on the Internet.

Forum statistics

Threads
189,203
Messages
4,314,294
Members
47,406
Latest member
GSB Machinery
Top