Search results

  1. dgjeynes

    Front loader for John Deere 6810

    Looking for a largish loader to go on my 6810. Ideally a quicke q75/6 or Mx 412 or equivalent John Deere loader
  2. dgjeynes

    Recommend me a steam cleaner

    Looking to purchase a steam cleaner needs to be single phase not budget but not top end. Just for general cleaning not used everyday. With a decent warranty
  3. dgjeynes

    Quicke brackets

    Anybody know if quicke brackets off a John Deere 6520 will be a straight fit onto a 6810? Been looking for a s/h loader and found this one be ideal if it’ll fit
  4. dgjeynes

    John Deere 3765 foragers job lot

    No rakes not for sale
  5. dgjeynes

    John Deere 3765 foragers job lot

    Tewkesbury Gloucestershire
  6. dgjeynes

    Loader to fit on John Deere 6810.

    Ideally want a mx or John Deere 3rd service and soft ride.
  7. dgjeynes

    R Tech mig welders

    Have a 180 mig. Great piece of kit also have a plasma cutter of theirs. Although this has not been as good.
  8. dgjeynes

    New tyres for 6810 deere

    Main jobs is on the post knocker but also do a lot of tanking and silage carting. Would like a bit wider but thought might hamper power too much
  9. dgjeynes

    New tyres for 6810 deere

    Have half thought of them. We’ve had a set on our loadall but not ran them enough to know them yet
  10. dgjeynes

    New tyres for 6810 deere

    Yes they’re not the budget tyre they once were
  11. dgjeynes

    New tyres for 6810 deere

    Don’t like them. We’ve got them on trailers etc and have replaced most due to side wall cracking
  12. dgjeynes

    New tyres for 6810 deere

    Currently has 16.9 38 and 14.9 24 but want to go wider. Looking at 520/70 38 and 480/70 24? I think those will work but not 100% sure. Will need wider front rims but rears are fine. Will be going down the vredistein route
  13. dgjeynes

    External pto switch retro fit on 6810 deere

    Is it possible to retro fit a pto switch onto these old Deere’s? I do a lot of tanking and it’d be nice not that have to keep climbing in/out the cab to switch pto on and off. Not sure if it’s just a case of getting the switch and plugging it in
  14. dgjeynes

    Wiring second beacon on jd 6810

    Best way to go about wiring a second beacon on my 6810? Not sure how John Deere would do it. Whether they run wiring back down to the fuse or cut and splice into the existing wiring. Advice please
  15. dgjeynes

    Jd 6810 fans

    All sorted now. Turns out one coil is knackered on the resistor pack and it was a fuse that looked good but obviously knackered. Having just done king pin bearings and seals it can wait until it fails again to be replaced. Taking the seat out really isn’t a big deal
  16. dgjeynes

    Jd 6810 fans

    I think on these if the resistor fails it’s either flat out or off
  17. dgjeynes

    Jd 6810 fans

    So I had no fans working. Taken the seat out freed them both up but only one fan runs. I’ve no power to the right hand fan at all and I’ve only got positions off 2,3 and 4 no position 1. Any suggestions?
  18. dgjeynes

    Zuidberg front pto leaking

    So I pulled this plate off to find this little tube broken off the end of the shaft
  19. dgjeynes

    Zuidberg front pto leaking

    Couldn’t get it out will try the bolt into it
  20. dgjeynes

    Zuidberg front pto leaking

    Removing that circlip did nothing. This is an old pto unit
Top