Search results

  1. T

    Manitou 634 does it sound ok?

    Seen a tidy 06 manitou 634-120lsu for sale. Have read the horror stories regarding the 90degree box. Has anyone a video or can the noise be described, does it be noticeable at idle or only when the boom moves. Sorry only have had JCB or matbro machines..
  2. T

    McConnel swingtrim balljoint

    Would anyone know where else the ball joint used to drive the cutter bar could be sourced? Is their another machine or vehicle which uses it. Problem is mcconnel want £220 for something that should cost sub £50
  3. T

    NH 6030 bent PTO stub

    What is likely to cause this to happen. It's a tractor I am thinking of buying, could their be any other internal damage?
  4. T

    Case 4230 Digi dash issues

    Anyone know what causes the entire dash to light up and stay that way? Have checked multi plugs for corrosion and earth is ok. Is their a way to reset it?
  5. T

    Hyundai Robex 180lc3 opnions

    Anybody have opnions on these older Hyundai's looking at a 1998 one seems reasonably good and reasonably priced. Also is their an export market if it's a bag of nails?
  6. T

    Single farm payment NI

    Anybody get a postal receipt for submitting this year's application in N Ireland???
  7. T

    Massey ferguson 42/43 rear mudguards

    Anyone know who makes fibreglass ones?
  8. T

    Claas sprint wagon gearbox

    Anybody got an old claas sprint silage wagon for breaking. Gearbox required its a 445p but any sprint should be same
  9. T

    Burley, Hampshire Hitachi EX 60 digger

    Anybody close to Burley willing to look at an old Hitachi EX60? Will pay for your time thanks.
  10. T

    JD 2040 high range problem

    Got asked to take a look at a 2040 that wont select high range but takes low and reverse in all gears. It is an sg2 with gears at side. Took lower pin out and gear stick moves into position freely so must be an issue in gearbox. Anyone come across this before?
  11. T

    JD 2040 high range problem

    Got asked to take a look at a 2040 that wont select high range but takes low and reverse in all gears. It is an sg2 with gears at side. Took lower pin out and gear stick moves into position freely so must be an issue in gearbox. Anyone come across this before?
  12. T

    Sanderson 725c hydraulics

    Had a look at a 725c today with a view to buying it. Anyway the guy said the hydraulics were a bit slow but had been sitting for a long time. So started it put the boom out and it wouldnt bring it back in. Also steering nearly locked solid. Boom wouldnt go up or down but crowd function worked...
  13. T

    JCB 526S Inverness

    Is their anyone close to Inverness who would take a look at a JCB 526S for me? Its not a dealer just would like to verify its not a scam ie no mechanical knowledge required. I will pay for your time as I dont really want to drive their from Northern Ireland unless it does exist.
  14. T

    Is a round baler chamber round

    Anyone ever checked this? Was looking at a waste baler which has rollers and have just noticed that the notional circle is not a circle.
  15. T

    MXM 130 Case cheffins

    Anybody see the 130 in cheffins last week? Its in the unsold lots looks good has just over 6k hrs and has the manual box 04 reg.
  16. T

    JCB 525-58 diesel in oil

    Got an old JCB 525 thats started putting diesel into engine oil. Changed heater plug but still doing it oil level up with only around 4hrs of operation. Its running fine so could it get in through lift pump without making it run rough? Obviously its probably injector pump seal but as always try...
  17. T

    Front-end loader: Other - MX

    Front-end loader: Other - MX Category: Front-end loader Manufacturer: Other Price: Open to offers Condition: Used Description: MX mallieux loader brackets complete with pipes and joystick. Will ft New Holland 40 series and TS with the 4 cylinder powerstar engine. Images: See the full...
  18. T

    Jcb 527-58 electrics

    Have an old 527 and she's not starting on key. Will start when bridged at starter. Think it's the start relay but don't know which ones which. Anyone have a diagram? Forward reverse lever does make one relay click so think it's OK.
  19. T

    JCB 525 / 527 mudguards

    Anybody know someone breaking a JCB 527? Need mudguards etc as mine are full of holes. N reg machine.
  20. T

    JCB 926 forklift

    Have an issue with an 1989 JCB 926, she isn't doing much wrong except for when you are travelling in either forward or reverse and move the shuttle to neutral she keeps engaged in whichever direction of travel you were travelling for a second or so. Everything else fine really. Do the solenoids...
Top