Search results

We can help you with that. Website is getting revamped currently but you can reach out to us off the website contact us and look for PN 1005089-01

If you are not doing any land leveling or tiling and just need the RTK for horizontal accuracy, i would recommend a trimble GFX-750 (or 350) with a Nav-900 and Centerpoint RTX Standard. The convergence time for satellites is under 15 mins and only requires an intermediate accuracy license...

I believe you will need both cables in order to run the camera: 114078 accessory cable and the 67259 power bus cable: https://agtogo.com/products/gfx-350-gfx-750-camera-kit-case-ih-xcn-750-xcn-1050?_pos=3&_sid=42a96f638&_ss=r

yes. there is auto brightness/dimness setting in main settings on display home screen or you can swipe down from the top of the display and there is a slider bar for brightness

You mentioned EZ-Steer... that one goes into the t2 controller directly

The ones we get from trimble are a expensive but you can buy the one for the Autopilot that comes with just the pins on it and then you can get your own connectors. https://agtogo.com/products/ez-pilot-pro-foot-switch-trimble-57259s?_pos=3&_sid=2a1ed5131&_ss=r $69.95 USD The expensive part...

we always have new ones... the used ones go quick but we get people once in a while trading in to go to nav-900

Yes, There are options out there. We use either a rocker switch option or the lift switch option with a whisker switch that would turn coverage on and off...

Was the angle sensor a case manufactured one? if so, Trimble Autosense has fixed issues like this before when Case sensors could not.

Pins 10 and 11.

The very newest NH tractors have the ability to allow the Nav-900 (with GFX-350/750) to plug into the CAN system of the tractor. This bypasses the need for the legacy NAVIII controller that is need for vehicles without that CAN plug in. The NAVIII has a valve driver for hydraulic control and...

The DCM 300 is 3G capable... I would suggest looking into the newer 4G modems as the 3G networks are systematically being shut down... or at least that is what the powers that be say they are doing. The GX450 and the RV55 will work for RTK cell corrections (VRS/NTRIP) and the SNM941 will do RTK...

The 350s are fairly new so only get them sparingly on trade ups to 750s... i dont expect a lot of used ones out there for another 6 months or so

For steering i would normally recommend the Trimble GFX-750 with EZ-Pilot pro but because you said you need implement guidance you would need to upgrade to the TMX-2050. You can choose EZ-Pilot (electric steering), or install hydraulic Autopilot system. If you could start with steering and...

I assume you are looking for 15 cm or under in terms of accuracy. The Nav-900 antenna with a GFX-350 or GFX-750 would be a good start. You can upgrade accuracy with rangepoint RTX or Centerpoint RTX for 15 cm or less and 2.5 cm or less. Steering wise, the EZ-Pilot would be what id recommend...

Trimble EZ-Steer with GFX-350 is basic option..... Intermediate is GFX-350/750 w/ Ez-Pilot Pro. both reasonably priced and high quality Steering Comparison Guide Display Comparison Guide

50 cm or 20" repeatable

https://agtogo.com/pages/trimble-gps-firmware

-27 is 36 spline and 20.75mm OD The other ones that are 40 teeth are -06, -39, -74 (39 & 74 have smaller ODs)

What is the Boss? The spline adapter cannot be purchased separately. The SAM 200 steering motor can be and its cost is around $3,000 USD. Usually the motor makes the original steering wheel sit up a little higher so they offer a more flush mounted EZ-Pilot wheel as well.