Search results

  1. D

    Mf combine 24

    Check the sides of the combine/chassis the cross shaft with the eccentric con rods on pulls the bearing on the u shaping side of the combine. (If left bad the pulleys hit on the left side of the combine) The pre cleaner idler (furthest pulley back) can give grief as belt is pulling it very much...
  2. D

    Best way to sheet clamp sidewalls.

    I just said, should have had flat plate with bolts for roof and handrail should have been highest point and smooth as possible
  3. D

    Best way to sheet clamp sidewalls.

    Any tips on sheeting the sidewalls, new style clamp, steel uprights with 3high pannels between and a hand rail 3ft above pannel 1ft below top of steels. Thinking of trying tyres on string 1 each side of wall with sheet draped over handrail. Put a tyre on each upright. Will string cut sheet...
  4. D

    Massey 6480 t3 just gone really aggressive and jerky on the shuttle and clutch at bottom

    A little bit of noise not much just put it down to spurious brakes, herd worse from others. Ccls
  5. D

    Massey 6480 t3 just gone really aggressive and jerky on the shuttle and clutch at bottom

    What are the springs made of? Steel or like a bakelite type material?
  6. D

    Massey 6480 t3 just gone really aggressive and jerky on the shuttle and clutch at bottom

    Just as jerky without using clutch (maybe worse) Same both directions. I'm thinking damper plate or clutch packs never been into clutch packs on anything before.
  7. D

    Massey 6480 t3 just gone really aggressive and jerky on the shuttle and clutch at bottom

    Is it the same pack for both forwards and reverse? Or would you expect 1 direction to have gone before the other? Any switches, would that still make it jerky without using clutch? Clutch has the arm type potentiometer. We think the spools aren't as fast, can anything be related?
  8. D

    Massey 6480 t3 just gone really aggressive and jerky on the shuttle and clutch at bottom

    Exactly the same today. My guesses Damper plate? But it's never rattled even then jerky isn't a symptom? Foreward reverse clutch packs??
  9. D

    Massey 6480 t3 just gone really aggressive and jerky on the shuttle and clutch at bottom

    Half way through bailing yesterday the shuttle has gone really aggressive even if you use the clutch makes no real difference. Any ideas? I'm thinking clutch packs? Also won't calibrate by holding shuttle above foreward and diff lock button just comes up CP on rh dash screen.
  10. D

    Cubicle house with tank over mining

    It isn't an ideal location but due to milk processing they done want to relocate the whole setup, cubicles are going to be 200m from parlour as is, don't want parlour away from processing so semi tied to this location. The size of the shed for 200+ cattle I think filling the mining is dearer...
  11. D

    Cubicle house with tank over mining

    I doubt any signing off, it's not a vertical shaft it's a long tunnel about 7m deep, with plenty of off shoots to each side. Then another main shaft with off shoots coming towards the first off shoots and to other side. Had plenty bore holes done to locate it and rods show it all
  12. D

    Cubicle house with tank over mining

    That's a building though, I'm picturing slurry storage being a whole different game. I see no reason why piling in a grid, strip footings supporting slurry floor slab/a pre cast option? Isn't viable
  13. D

    MF 6480 front suspension

    any one find a good supplier for the Accumulators?
  14. D

    Massey 6480 brake master cylinder leaking

    having the brake accumulator tested, the front axle one is dead, where is best to buy one from, 27mm x 2mm male thread on mine which im struggling to find other than MF
  15. D

    Cubicle house with tank over mining

    Has anyone ever done this or know the rules/ regulations wether you can site a cubicle house ideally with a tank underneath over mining? The mining is 7.some m deep (found by drilling) A separate location for the tank would have to be 200m near an existing gateway for access and still need...
  16. D

    Concrete Panels Supply

    Another low Grange vote here
  17. D

    Liberator on emerging spring barley

    Nice damp seedbed from last night's rain near perfect for pre em? Would have stuck to tyres slightly 10am It's on now anyway. 15 acre field 6 acre drilled Thursday odd patches poking green up (wetter spots 🤣) rest drilled Saturday perfect just white shoots out of seeds 1" down. Black and...
  18. D

    Liberator on emerging spring barley

    the label says up to gs 23, 24, 14 for wheat and winter barley. But pre em for spring barley
  19. D

    Liberator on emerging spring barley

    We have some barley just emerging and I wanted to pre em it but didn't get to it for many reasons. Will it do a lot of damage 0.3l/ha Thanks
  20. D

    Massey 6480 brake master cylinder leaking

    Are both of these accumulators not just T into same hydraulic circuit? What pressure should they be set at?
Top