Search results

  1. Niall310

    Krone mower bed problems

    We have a few krone mowers, we bought this 10'6'' trailed mower new, in 2015, it has done a fair few acres but the triples have taken over most of the work the past few years. Long story short, when changing a module bearing we noticed play in the back idler gear so we took out all the...
  2. Niall310

    JCB 434/416 opinions

    As thread suggests, I'm looking opinions/expierence of 434's or 416's using them up to and over the 10k hour mark. Any common problems that might occur pre or after 10k hours or common problems to look out for when buying one as we're probably looking for one around 5/6k hours. We currently...
  3. Niall310

    Rear Discharge Spreader-Canopy

    I need to make a 'simple canopy' for a Bunning 120 widebody. I've been told a lot of people make them rather than buy so I'm looking if anyone has any photos of 1 on or off the spreader as the ones on the website aren't great. -roughly how close is the canopy to the tips of the beaters? -what...
  4. Niall310

    EBAY 20T Bottle jack?

    I need a new bottle jack, there's several on ebay from £25 up with no real differential between them. Has anyone any recommendations for whats what? TIA
  5. Niall310

    Homemade Hydraulic Bench/Bearing press

    Has anyone made their own floor mounted press? Use a bottle jack upside own or use redundant rams from around the yard? I've been keeping my eye out for a while but nothing suitable has turned up. A few flimsy looking ones on Ebay and any decent s/h ones would cost to much to get delivered to...
  6. Niall310

    Gas bottle trolley ideas

    Hi, I just hot a set of oxy/propane bottles and need to make a trolley for them. I'm just looking for any ideas or pics before I start if there's anything worth including..or not including. I was thinking big wheels so its easy moved on rough ground. Thanks in dvance
  7. Niall310

    Umbilical reeler sides

    Does anyone know what type of plastic is used on the side of the reel? or a suitable plastic for the job? I know these ones are molded but just a simple colored sheet would do. Also is the side sheeting useful from a practical point of view or is it just for the looks? Thanks
  8. Niall310

    Straightening a 10 stud axle

    I've an ADR 10 stud axle (square beam) that has a small bend in a single spot. Is it worth trying to straighten or a waste of time? Anyone done it before with any success? Also, any suppliers of 2nd hand ir new ADR axle parts? Thanks in advance
  9. Niall310

    Claas 492-890 etc. chopper breaking?

    Hi, does anyone know of a claas 492 breaking in the UK or Ireland? Thanks in advance!
  10. Niall310

    Krone Triple mower issues

    We have Krone B1000 's and have some grouper issues. Last year we had trouble with grass getting inside the grouper (between the belt) and building up on the rollers. It also built up on the perforated plate between the belt. It would stretch the belt if left and take more drive to get it to...
  11. Niall310

    Deutz TTV Opinions

    Hi, we're currently looking at buying another deutz. We run a150.7 and an X720 and now we're looking at something 180hp to 200hp. Ideally a 180.7 or M650 if one could be found but we've come across the odd TTV 630 for sale but we don't know much about the deutz vario's as they're not common...
  12. Niall310

    Deutz TTV Opinions

    Hi, we're currently looking at buying another deutz. We run a SAME 150.7 and a Deutz X720 and now we're looking at something 180hp to 200hp. Ideally a 180.7 or M650 if one could be found but we've come across the odd TTV 630 for sale but we don't know much about the deutz vario's as they're...
  13. Niall310

    Mueller Tank plastic cap

    Has anyone had any problems with the plastic caps on the outlet cracking and breaking? This is the second one in a few years and we've taped them but that only lasts so long. Any solutions or cheap places to buy caps? Thanks in advance
  14. Niall310

    Trailing shoe with mounted reelers

    We're looking for a S/H trailing shoe to suit 4 point linkage on a current tanker. We'd like to keep our options open so it would be ideal if it could work with a mounted reeler on an umbilical in the future. Has anyone adapted trailing shoes to work with mounted reelers or vice versa? Also...
  15. Niall310

    SAME Iron/Deutz 150.7 4WD Shaft replacment

    The splines on the 4WD stub shaft out of the gearbox have become worn, causing a vibration. The dealers have said it is common as the 4wd shaft guard means most people don't see the grease nipple on the female end of the shaft. The 4wd shaft is rigid and the sliding is done on the splines on...
  16. Niall310

    Front Mower-Distance between wheel & mower

    Hi,We just got a front mower and sits very close to the front wheels which seems to be because of the 38'' front rims and the axle position. There is only 3-4'' at most between the mower wings and the wheel, and when the axle tilts and is on full lock, it's down to mm. Has anyone had a similar...
  17. Niall310

    NC Paint Code

    Hi, Does anyone know the NC Standard 'Orange' paint code? Thanks
  18. Niall310

    Silage Trailer Refurb

    I came across these photos of our Herron we refurbed 3 years ago so I thought I'd add them here for anyone that's interested. The high sides had been bowed out, the top and bottom of each extension was rotten and the latch for the grain door was bent and the bosses holding it rotted through...
Top