Search results

  1. Andy26

    Claas Arion 640 error code/ runs but no controls and stuck in one gear.

    It's probably the Auto 5 module, they tend to degrade over time, starts off you can turn the tractor on and off to clear the error and progressively gets worse. It will default to B1 and only the foot pedals and the rear fender controls will work. It's a laptop job, I'm surprised your dealer...
  2. Andy26

    Kverneland Accord TS Tine drill

    @Zippy768 I've attached the operators manual as a PDF below.
  3. Andy26

    Kverneland Accord TS Tine drill

    I think they're designed to operate at 4500 RPM max, so around 4000 RPM will be fine for most crops.
  4. Andy26

    Lorry Trailer Sheets

    If it's four holes as you've described, you would only need to worry if the trailer was going to be parked up for months, if it's going to be tipped the same day or even the same week it will be fine even if there's an inch of rain.
  5. Andy26

    Lorry Trailer Sheets

    Whilst it's not ideal, it's hardly going to have any effect. I really wouldn't worry about it.
  6. Andy26

    Top/middle link shear.

    Looks like there's a shopping trolley to for good measure. Is it a front linkage, it's hard to tell. Doesn't look a very big or strong ram cylinder in comparison to the linkage and drawbar pin etc.
  7. Andy26

    Today at work

    Must of been handy drilling the field behind your house?
  8. Andy26

    6 metre Vicon LZ 520 Disc drill

    Yes they are, has a feed roller like a MF30, in fact they're were built in the same factory. Looks a nice tidy drill (y)
  9. Andy26

    Contacting the " Management" of tff

    Yes there's a time limit on editing a post. Thread was removed a few days ago as requested (y)
  10. Andy26

    Simba Freeflow 3m operators manual
  11. Andy26

    Project Xerion.

    Perhaps @Cab-over Pete you could trial asking customers to supply a loader, surely every farm has a telehandler or decent fore end loader. There's always compromise, it reads like you're compromising the best spreading vehicle, the Big A, to be able to tow your own telehandler. It could be...
  12. Andy26

    Will LAMMA 2021 happen

    Agtitechnia Nov 2021, Sima Nov 2022 How much further apart do you want them?
  13. Andy26

    Stubble cultivator?

    Doing the same today all be it with auto reset, a tined cultivator can remove compaction and wheelings from harvesting and spraying, which is where the short discs fall short imo. In a dry year or if you have a combine on tracks then it's perhaps not a problem. @Poncherello1976 looks a decent...
  14. Andy26

    Stubble cultivator?

  15. Andy26

    Splitting a right of way maintenance obligation - is it just a matter of division?

    This example is different, land that already enjoys an access right has been sold, unless there is a clause to limit this right being transferred to successors in title then land or parts of land can be sold and utilise the right of way. @fieldfarmer example is using a lands access right as a...
  16. Andy26

    Spring barley volunteers

    Aramo/Falcon/Fusilade will all do the job.
  17. Andy26

    Spring barley volunteers

    More likely there are tiny weed shoots, just very difficult to spot.
  18. Andy26

    Parts prices....again!

    I tried several times with a similar result. If you ask a local dealer who is a Kramp dealer they can set you up, whether you get the discount is another matter. There has been a big push in lockdown by Kramp and their dealers to get customers signed up with accounts.
  19. Andy26

    @Alternativedairy contact details?

    Yes Del Boy arranged for a friend to buy them all, so as to give Rodney some confidence. The friend went straight to the scrap yard to get rid of the old lawn mower engines, where Rodney proceeded to buy them all back... 'because they can't get enough of these down at the depot' :ROFLMAO:

Forum statistics

Latest member