The lever that controls the arms on our JD 1950 has a very small parts of its range of movement which affects the arms position. It is difficult to fine tune the position. There is a lever beside the arms and I've played with it to see if it would effect the granularity of the lever/arm...
Does anyone here have one or used one?
Going to be doing some reseeding and looking to find out exactly what I'm putting on after getting the soil sampled.
Are they with it and where can they be bought?
Has anyone here done any work to protect river banks from getting eroded?
Got a river flowing along our boundary and it is starting to undermine a tree on the bank at a bend in the river. I'll not have access to get a digger in to do work - unless the contractor can get in upstream.
I was...
Got some field gates that are hinge bound before they can be swung around against the fence - fence is in line with the gate.
Has anyone seen a cranked hinge (L shape) that can be mounted onto side of post that will allow the gate remain centered when latched, but swing back to rest against the...
Hi.
Got a small herd of 9 cows. I want to use FTAI on them as I don't think a bull is feasibly for such a small number.
These cattle would trend to spend most of summer at an out farm where they would be checked daily on way home from day job - so genuinely every 24hrs.
I'm trying to figure...
Hi.
Looking to get a gate made for handling facilities and to make the most use of the area I want a gate that I can swing from both ends.
Has anyone seen any good implementations of this? I've seen some which have eyes on each gate end, but to open you have to pull a bar up the full length...
Hi, I've got an Isuzu D-Max and have the problem of tools and implements in the load bed sliding up and down. I was going to put down a carpet in the rear to prevent this, but before doing so was wondering if there were any solutions for sale that covered this problem? It already has a load...
Looking to get some round bale silage tested. I've got no corer to test the bales and looked online to see what was out there. They seem a bit expensive so I was wondering if there was any cheaper way of coring the bales to get samples out? The items online seem to be £150+
Any ideas for a...
Selling a truck body on eBay at the minute. It has been up a while now. I've just received a low ball offer from a user account with no feedback that was created in 2010.
Seems a bit odd that the account would be dormant for 12 years. Is it worth engaging with this account or is it likely to...
Need to make some 90 degree bends in 2mm or 3mm flat steel.
Is there a cheap bender out there that I can get for this - will be making a large number of them for a project - 150 items each with 4 bends. I suspect that an engineering firm would charge me a fortune for doing this monotonous work...
Got a 14ft dropside lorry body in very good condition for sale. Not getting anyone sensible online - only folk wanting to chat and/or not turning up so would like to sell it on to get shot of it.
Is there anyone I can contact who buys these in for selling on or export?
In the market now for a new jeep and narrowed down to these. What are opinions on both - will be looking at manual? Cost and delivery times might push towards a D-Max, but Hilux is the preference.
Also, does anyone know whether the NFU discount is worth going for? I got the impression their...
Hi,
Would anyone be able to upload some photos of how they retrofitted a softride to a front loader?
Can they go anywhere in the circuit or must it be connected in a specific place?
Is there much of a difference between those with 2 bottles - presume they are of differing pressures for...
Looking to get a new 4x4 as current one has terminal chassis issues.
Can anyone tell me what are the offers that the NFU have with Toyota for the Hilux and Isuzu for the D-Max?
Anywhere else I should be looking for deals? I expect that the waiting lists will be considerable, but considering a...
As per the title - will be putting up a new handling facility on an outfarm within the next year or so, depending on funds. I've got an idea of the layout in my head, but before I commit to it, I was wondering about curved forcing pens - primarily their cost and their worth.
It would be a...
Just seen this whilst searching for sliding gates for a cattle crush. Searching various forums has shown that Kellfri have a reputation for lower quality products - although these were reviews of more complex machinery.
I've got a small suckler herd and this seems better value than anything...
https://www.nrplantmachinery.co.uk/listings/2016-mccormick-x6-430/
That is the road end used by AFM Tractors. Not to mention that the prices are nearly 1/3 of what they should be. Although odd that the company number correlates at Companies House.
What's the story with these guys?
How is the red text below to be interpreted - having a debate with another person about what this means - I think it is #1 - he thinks it is #2? Who is right?
What combination of (i) - (iii) are defined here?
Is it saying distance can be reduced to 3m if:
1. incline of less than 10% AND...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.