Search results

  1. Rick.banks

    Tub mixer wagon : Rear side conveyor medium

    www.enegis.co.uk seem to have a few feeders about normaly, might be worth a look (y)
  2. Rick.banks

    Modern classics. What will become a classic in the future

    Nh t6000/ case maxxum both pre adblue
  3. Rick.banks

    What do you use to clean cubicle beds?

    Upside down rake (y)
  4. Rick.banks

    What's the quality of Granit Parts?

    Had quite a few parts from Granit, seem very good, also seemed a lot cheaper than Kramp at the time
  5. Rick.banks

    Kuhn suppy problems

    Update, it has now arrived and been used [emoji12], was another mixup with the drawbar kit, the wrong kit was sent to the dealer, so has been in there nearly two weeks
  6. Rick.banks

    Kuhn suppy problems

    Ooh that will upset my rep, he's waiting on 2 mowers to turn up too
  7. Rick.banks

    Kuhn suppy problems

    I did message kuhn uk direct through Facebook, wasn't really expecting a reply but they were really helpful to be fair
  8. Rick.banks

    Kuhn suppy problems

    Just heard it has been loaded up on a lorry this morning so fingers crossed 🤞
  9. Rick.banks

    Kuhn suppy problems

    I think this may also be my problem, the transport, they have said transport is letting them down, I'm just irritated that the deals done, I've not got the machine and I've done all my first cut baling
  10. Rick.banks

    Kuhn suppy problems

    Best part is nobody seems to know where it is, I know its built, there's a serial number!
  11. Rick.banks

    Kuhn suppy problems

    Father in law had similar problem with a high tip Thwaites dumper, one week it was July the week after when ordered it was September, then the week after they rung up and said its gone up £800 [emoji85]
  12. Rick.banks

    Kuhn suppy problems

    I understand there is supply problems due to covid and even brexit but 7 months now for a 4 month order takes the mick
  13. Rick.banks

    Kuhn suppy problems

    I still have the machine I've traded in that I am using, the dealer is doing all they can to be fair
  14. Rick.banks

    Kuhn suppy problems

    Whats the record for ordering kuhn kit and it not turning up? I'll start... ordered a baler 7 months ago for march delivery, still not here... can't be on my own here!
  15. Rick.banks

    Mchale f5500 or kuhn fb3130?

    The 35 seems to be the same baler as the 30 couple if extras bolted to like auto greasing more knives etc, be like the f5500 to the f5600, thats the way I've seen it anyway, going to look at a 3130 and 3135 tomorrow as haven't seen anything of them before
  16. Rick.banks

    Mchale f5500 or kuhn fb3130?

    Not really after something with all electrical settings, dont mind a few, like a good screw and a tap here and there [emoji38]
  17. Rick.banks

    case maxxum 150

    The only difference between them is 100kg in weight ...the 2 extra cylinders basically
  18. Rick.banks

    Mchale f5500 or kuhn fb3130?

    Father in law has run a f560 and 2 fusions, in the last 10 years or so, never had a bother with them, my biggest problem is the drawbar, I pull wrapper behind, mchale won't supply one any more, however the price I have for the khun is cheaper and Includes a drawbar kit
  19. Rick.banks

    case maxxum 150

    Don't think I could go back to sle now 🤣🤣
  20. Rick.banks

    Mchale f5500 or kuhn fb3130?

    Not too sure reel wise but do know it has hydraulic rotor disengage so can stop the rotor spinning net the part bale and chuck it out moving on from a welger think the mchale is very similar to what I have now pick up wise apart from camless and 5 tine bars
Top