lately our 6930 has been making a different noise when braking , sounded a little graunchy , not really metallic but hard to describe , maybe like a dry rubbing noise ? Thought brakes ,
so got JD man out , took for a drive , found that no it’s not in brakes , seem to be on over run when 4wd is...
New to this operation , but it has been thrown to me to look into. Firstly , do you need a creeper box , I’m bit concerned the tractor here may be too fast in first gear at pto speed .
secondly , I would prefer it be three point mounted as opposed to axle mounts as the tractor does other duties...
Recently pulling the rake up the road , our 6930 suddenly developed a vibration and lost power , didn’t sound right , pulled into the job , checked , turned off and restarted, seems ok now . Suspect she may have dropped an injector?? No warnings came up , but have these fault codes showing.
I...
just noticed on our 600 lely that the bar that stops it swinging ( ie the bar that the locks it with multiple holes in it ) flex’s, has anyone else noticed this , it’s rather disconcerting to watch , and think if it’s unusual we better replace it.
Thanks
Wondering how to set the hydraulic pressure for lighter floating over the ground? Should the accumulator press be higher or lower to reduce ground pressure ?
thanks
Find our 6930 hard to start when cold , checked fuses and relay for glow plugs , all seem ok ,changed battery , earth feels tight . Are there any fuses for glow plugs other than on top of the engine ? Notice when you turn on the ignition the glow light on cluster goes out with all the other...
Recently seen a couple of videos on you tube with operator’s running Claas 3100 / 3200 front mowers and 3050 / 3150 rear mowers.
I thought the 3050 was only available in 540pto and if so how are they operating the front at 1000 rpm?
Any one have any experience operating this combination?
Thanks
Got a new to us jd 6930 , was looking at a 3m rear mower ( mounted ) , but thinking it might take upto a 3.4m ? what are your opinions, bearing in mind we mainly mow hilly stuff! Also has front hitch so will add front mower one day maybe . Oh also straight disc mowers , no conditioner.
Cheers
Looking at a second and tractors to suit our operations , and just wondering about pto hp into implements.
So tractors will be for mowing and baling mostly ( round and possibly the conventional if required , tedder and rake )
Was concerned that too much hp from the pto could damage the balers...
Looking at possibly buying our first brand new mower , currently have a Claas disco 250 , but looking at the above brands , and somewhere in the 2.8 to 3m size.
What’s people’s experience with these brands?
Seem to have a vibration at the input shaft ( where pto drives) have had the belts off , drive pulleys all seem smooth , can rotate the discs and they feel smooth and normal . Bearing housings etc all seem normal operating temp , just can’t figure out what could be causing it . Any one else had...
Ok so broke my vote 1510 pickup drive shaft , two to three weeks for parts supply and approx 5k to repair. So been looking at a second hand Fortima 1500mc , what’s people’s opinions on these?
Thanks
Opinions on these tractors? Cebus or cis ? Being a JD man , I am unfamiliar with them , but as no available good second hand Deere’s about , have seen two of these both at approx 5500 hrs ( can’t afford newer ) , one with the cebus command arm thing and clematis , one with hexashift and manual...
Done a module , but found the two studs above the idlers are spinning, any one had any success with fixing them , do not want to split the bar! Also when reassembling the module they have an o ring , but is using a silicone gasket goo around flange required as well?
Thanks
Looking at the above just under 10 k hours. Had it appraised by jd expert , ok , but needs head gasket and some play (20mm) in rock shaft, front axle diff and tls just been overhauled. Not much else ever done to it apparently.
At these hours should I run a mile or are these tractors ok for a few...
What are these tractors like , been looking at second hand Deere’s but price and spec this one is a fair bit ahead , but we are unfamiliar with NH . On the specs online , rear lift only 3.5t , yet 6830 deere is 8t , is this correct?
What are they like to operate , reliable ? The one we are...
Looking at getting a combi to save some time , running a VP1500 at the moment. Looking at videos of combi packs , do you have to shut off the pto to transfer the bale to wrapper table? Any other advice / experience regarding these combi’s . Also recommended hp on hills , as I think they are...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.