Search results

We have a new Holland t7.225 with receiver and nav3 controller. It’s unlocked for Rtk but need a modem for the sim. Are there any after market modems and cables available?

Anyone running 420/95r50 on a gen6 fendt724? I have measured as best as i can and it does appear there is room for them. Tightest spot is on the exhaust side at the bottom of the plastic trim.

As above looking for a tidy 741 manitou. Between 2-5000hrs but condition more important.

As per title, looking for a 17ft 5.2m power flow header.

Preferably a mf, new holland or similar as we already run a 1010. Condition is more important than age.

After seeing an American sprayer on fb I am considering getting our sprayer coated. Auto smart matrix claims to give 8 yr protection although you need to be careful with tfr and preferably give it a top up once a month. The top up is applied like snow foam apparently. Has anyone any experience...

Does any one know of a Lemken kompactor for sale? 4-6m in good working order.

We tried to start irrigation today but as usual ran into problems. Have all sorted but my komet gun will not turn by itself. It is quite stiff to pull round by hand. I stripped it apart this evening and it appears to turn on an upper and lower nylonplastic circular plate. The lower one was hard...

Our kv eg plough is leaking oil from the grub screw in the end of the ram next to the third pipe. Tried tightening it but oil is still running out of it. Anyone else have any experience of this?

Either of the above prefer an 828. It must be profi plus and preferably still in warranty.

Is anyone running a newholland hd or a case optum. If so how are you finding reliability, power and to drive? Is there much advantage over a long wheel base t7? Thanks

Looking for a 3000l horizon or vision Sam sprayer. Preferably 2014 or newer with less than 3000hrs. Dual ride, gps section control, 600 flotations and 380 row crops, 24 or 28m variable geometry boom and 400l pump all preferred spec but not deal breakers

Looking for some user experience of a MF 4347pl or the Fendt equivalent. Have they been reliable? Is the parts back up and product knowledge good. I know these combines have taken there dna from a Laverda which were always well regarded.

We have the chance of trading up our cx820. We are considering a 630 Montana or a cx8060/8070. I realise we are comparing a 5 and 6 straw walker but 650 Montana's appear hard to come by. We are based in the very nw of Ireland and regularly cut grain at above 20% and straw is very important and...

Hi I am looking for a Trimble modem and cables to suit a New Holland with a 750 screen & nav 3 controller.

Looking for advice I have volunteer wosr and potatoes along with some groundsel, chickweed and wild oats. Wheat has just had t1. What is my simplest most cost effective method of control? I used tower at 2l/ha in the autumn. Thanks

I am looking a quote for 480/80 r46 Tyres and rims and matching front tyres and rims. To fit a Fendt 720 on 72”track. Preferably 380/85 r34 on front but 420/90r30 would do. Thanks

We are looking to upgrade our work hilux. James McPhee has a hilux I’m interested in but after reading the reviews online I’m not sure it’s worth the journey. Has anyone had any dealings or knowledge of them?

Looking for advice, returns cutting oats are running very high. Oats are a good crop but badly laid and very ripe. I have opened the bottom sieves to 10mm top sieve 9mm concave 12mm anymore it's not threshed. Reducing the concave speed to 550 and the wind to 500 helped but unable to do much more...

Looking for some advice. I need some parts for the propellor and for the Komet 140 raingun. If anyone could point me in the right direction it would be much appreciated