Going to look at a JCB tm 300 early next week. 5500 hrs.
What are common weaknesses of these machines. Wear and tear on all pins and bushes I’ll be checking.
What about the mechanical bits?
Howdy.
I have a 3.6 meter front mower. Looking for ideas to stop it bulldozing when cutting.
Last year we had extremely light crops. Soil would build up of the skids and cause it to bulldoze. If it was raining it worked perfect as the soil didn’t stick and if it was dry it was ok but in...
Would anyone have a contact to mx loaders in the uk. I need to get in touch with someone who can get me in touch with the factory.
not having much luck contacting them direct yet and looking to import some loaders to Australia.
any help much appreciated.
Richard
Recently got a new gen 6 936. Just wanting users opinion on adblu usage as it seems to like a drink.
currently it’s using 10.5 % of fuel use. This seems a lot to me on relatively light work at the moment. I’ll have it on a deep ripper next week but slightly concerned how much it will use on...
Has anyone used a taurup 9177s rake. Need a rake and have found one of these at not silly money just wondering if they are any good.
any information on taurup rake helpful too
Does anyone know of a good supplier of these marker boards that don’t cost an arm and a leg like the manufacturers want.
I want to add some to machinery here but haven’t time to make my own as I’ve done in the past.
preferable in sticker form for easier freight and I can stick them to a board...
Are these units sold in the uk. Looking for users specifically running them on Fendt isobus displays. Mainly looking seeder controller but sprayer can be discussed also.
Richard.
I am trying to get a vra map uploaded from a trial version of Trimble ah software onto my Vario terminal.
Has anyone done this and how did you do it. I seem to be missing something.
I have the above machine. The hydraulic tank low level light and buzzer won’t go off. It does my head in. Any idea why and how can I bypass it.
Need it gone
If converting a trailer on air brakes to hydraulic is there a ram available that will bolt onto where the air brake chambers come out.
Obviously I could get the combined air/hydraulic setup but not looking for this. Asking here as no one I know of supply these down here
anyone know what exactly is involved in getting with topcon or Trimble base station correction signals into jd Rtk steering. I’m fairly sure I’ve seen a topcon radio on a Deere but don’t remember the specifics of it.
Does anyone know if the Fendt varioguide using Trimble reciever on Rtk can accept a topcon Rtk signal.
If so what needs to be done differently.
Hoping you @Pheasant Surprise might know
need some ideas for a mate. He has the above which works fine until it is stopped and the battery isolator turned off.
On restarting the tractor the dynashift and pto won’t work. The dynashift leds A and C flash alternately with B and D.
All power supplies and earth cables checked and in...
Has anyone dealt with trelleborg on a tyre warranty claim.
We have had a tyre fail. (710/75r42) got a new one and replaced it as needed to keep going.
Pictures taken and all necessary forms sent in. Tyre has approximately 70% tread left on it. Always had pressure set higher than recommended...
hi all.
I have the above rtk base station and would like to get more details stance out of it.
Does anyone know of a simple way to set up a repeater to run off it.
hi all.
I have the above which has decided to beep continuously telling me the oil tank is empty which it is not.
Is there any way I can bypass the sensor to test if it is faulty before I go ordering a new one.
The contestant beep is driving me bonkers.
Richard
i have the above machine and need to change the rubber strips on each side of the sieves.
Anyone done this and have any tips on how to do this. They are bolted in and the nuts don’t appear to be captive.
I have bought a 2005 model of the above on condition that it's ok after I view it on Monday. They are to presssure test the vario as its original.
What else to look at. It's done 8000 hrs but looks tidy from pictures. Not had anything to do with the old shape ones just the new ones hence the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.