Search results

  1. T

    Case international 895

    Hello all I've a diesel leak on pump on 895. It seems to be coming from where the throttle linkage enters pump. Is this a job I can do myself? I assume pump will need removed and will that upset timing ?
  2. T

    Mechanic N. Ireland

    Hi Anyone know a good on site mechanic in co down. Need work done to a case international 995
  3. T

    Case 895

    Does anyone know where I can buy these hydraulic lever link arms or will it be a breakers yard. There adjustable too.
  4. T

    Potato issue

    Put in a small plot each year but this year half the leaves are curled but other half is normal. I'd put manure on the ground where the leaf curling has taken place but not where there normal. Could it be frost? The odd one is fine among the curled ones
  5. T

    Hi-line trailer

    Anyone got a 10x 5 scrap hi-line car trailer lying about. Think they were made in Derby
  6. T

    International 895 lifting ram

    Anyone know where I get a rear lifting ram for my 895. Theres two on them but I'm missing one. Is there a left or right hand side or both the same? Thanks in advance
  7. T

    Trima 1190 4 loader

    Has anyone got one of these loaders. Looking dimensions for the brackets that are used for removing loader or if anyone has brackets for it that I can purchase. Thanks
  8. T

    Case 895 rear arms linkage

    Hello all. Some implements are catching the rear wheels so I need to extend the rear arms. I can lift a lever and extend the rear arms but it's very flimsy. I'm I missing something here or is there another way round it. Any advice greatly appreciated
  9. T

    Case ih 895 1992

    Hi all Anyone know where I can find the chassis number of this tractor. I've looked on the front axle to right of radiator but not there. Looks as though a plate has been there though. Is it stamped anywhere else? Any help greatly appreciated
  10. T

    Case clutch

    Gonna need a new clutch in my case 895. Any trustworthy mechanics/technicians in N. Ireland. Preferably co down
  11. T

    Loader hoses.

    Need to fit new connectors on hoses. Any need to depressurize and what oil will I lose. Do you need to bleed system afterwards?
  12. T

    New 10 x6 tipping trailer

    Anyone know what I'd be likely to pay for a brand new tipping trailer 10 X 6. Dont need lights but I'd assume they come as standard
  13. T

    Case 895 diesel pump leak

    Hello I've a leak at the diesel pump which is circled in picture. Can I remove that nut and spring and is there likely to be a oring or seal below that .
  14. T

    Case 895 alternator issue.

    Hello all My 895 had stopped charging and removed the alternator only to find the adjusting arm for the alternator has been butchered. I would imagine this is pulling the alternator to the side once tightened and destroying bearings and brushes pretty quickly. Anyone know what actually holds...
  15. T

    Nature at its best

    Found these willy wagtails in the tractor today just below radiator. Tractor used everyday. Never experienced this before with a tractor in constant use
  16. T

    Trailer id

    Hello can anyone help id the trailer, about 30 yr old, I bought it in england for vintage tractor movement, has a galvanised chassis, knotts brakes and Bradley tow hitch. No id plates on it anywhere
  17. T

    Trima loader 1190-4

    Hi all I've a trima loader on my case 895 but main valve housing is leaking badly. I think the loader is quite old. Anyone know the best place to get new deals, emailed a few but no response.
  18. T

    What series is my case

    Ive a 895 1990 case, how do I know which series I have?
  19. T

    Case hydraulics

    Hi all Recently bought a case 895 with front loader. Using a ripvator rear forklift. I've 2 sets of spool valves. Need one for tilting top link in and out and 2nd one for lowering and raising the forks. Prob Is when I use the lever to lower and raise the back arms it only lifts slightly but if...
  20. T

    Case 895 operators manual

    Hello, I'm looking to purchase a operator's manual for the above. Anyone know where I could get one. Thanks
Top