Search results

I have never done my Zam to run sections, and the main problem is why I have ZAM comfort model, which is not section control ready, it must be the hydro version you have… I have tried to run it by many different ways, by amatron3 Gps switch, by Trimble tmx ASD serial connection, and by Trimble...

anyone knows, can ZA-M spreader (ProfiS) equiped with Amatron+/3 and Comfort package be section controled by GPS switch, Amatron 3, or other GPS device (FMX)?? or it must be only Hydro version?? I know, hydro has predefined 6 sections, but if it is not hydro, it should also be capable to run 2...

I have an amazone uf sprayer with amatron 3 computer using with gps switch section controll in amabus mode, working great... I also have ZA-M spreader working with amados + computer.... now I want to upgrade my spreader to work with amatron3, so I dont need to replace screen al the time, and...

The main question is: Can I from boundary shape file in the Trimble farming Core software make a headland pattern guidance line… adding one of exsisting AB lines as an infill line??? then is not a problem drive the boundary following lines by autopilot and get perfectly straight boundaries...

Yes, i have already known that… But I want to use my AB lines around the field which I have already had, and drive around the field using autopilot, and make a boundary line using field mark set as boundary… After that I want to set that boundary line as headland guidance line with adding one of...

Is there an other way to make a fully functional field boundary then using the headland mode? I would like to make them by using field mark option, while driving autopilot on exsisting ab lines, which I have already made in my fields… I tried that today, but when I finish boundary, it is saved...

We are drilling soyabean after winter barley like a secondary crop with vaderstad rapid drill… first pass we go with vaderstad carrier 650 disc harrow, and after that we go drill… and have troubles that drill can not penetrate and put seed deep enough, because after carrier pass there are lots...

Does anyone have pinout of ag Leader 4000315 cable?? It is 12 pin deutch to a male db9 standard cable… I need that cable to connect a vaderstad control station to the ag leader application rate module… I have already had a 4000309 cable with female db9 on its end, and I tried it with a null...

I want to upgrade firmware on my ag262 receiver to a higher, so I can use modem to receive rtk corection data... I have instaled version 1.xx, and it should be 2.0 or higher.. I can only find the newest version 5.2 or 5.1, but flash loader doesnt want to instal them... anyone know where can I...

Hi, Could anybody please tell me which software version for controll station controller do I need to use it on my rapid drill?? One I have installed does not support it...

Yes I know for 252... But I thought, if it is only for Waas in price of used 252 maybe I can get a new one 162... but I found later, there is a problem about 162, it needs an unlock for autopilot, and you can buy it only in USA... so maybe is an used 252 realy the best solution for what I...

I am trying to find a cheap antenna which will work with nav 2 controller.. i already use one setup with nav2, aggps262, and an old agleader insight display, and it work just fine for me... since I have one more autopilot ready tractor and one extra nav2, insight, and all the wireness, all I...

A week ago I bought 2 pieces nav 2 controller, and one more insight display (autopilot unlocked)... One nav 2 I hooked on my massey which is autosteer ready, and autopilot works propertly... I had some problems with nav controller calibration till I found out that I need laptop and toolbox 2...

Ok, thank you!

Is there some other (cheaper) controler compatible with those components, or it will work only with this trimble nav2???

hi... recently I have bought a used mf8660, with trimble receiver 252 on the roof, and ag leader insight monitor (autosteer unlocked) in the cab, and there is, in the cab, on the right one missing part, some computer unit... i think there fits trimble nav 1 or 2 controller, but I am not...