Search results

Hi, i have a case ih 885 2wd, one of the last 885s, intratrac say it's actually 895 in disguise, But lately the steering wheel spins but the front wheels don't respond for ages, it's better at full revs but still not great, rear linkage seems to be working OK, no obvious leaks, so thinking...

Hi im looking for a loader for my case 885, must have euro 8 cradle fitted, self level would be nice but not essential. Thinking quicke or trima but anything with euro 8 would do, not looking to spend the earth though. Close to or in Devon would be nice What have you got? pm me with pics and...

Hi does anyone have any clips or clamps to hold the skims in place on a Lemken DL120 plough? Circled in pic

Hi does anyone recognise and know what make this subsoiler is, i need to order some parts, sold by Murley agricultural supplies

Can you telL me what engine code DT2D315173* Is for please

Hi everyone, I've been offered the chance to buy an ih 674, but its got knocking big end bearings, so what is the best option to repair it, full rebuild is probably too time consuming, but what about an engine swap, would any of the newer model engines bolt straight up in it's place? If so whats...

Hi bought this roller as spares recently and wondered if it can be repaired? Attached pics

Hi Does anyone here have a parts diagram for a Bomford Subsoiler? or know what should be where? I have picked up an old twin leg subsoiler, and it had a couple bits missing on one leg, ive managed to source a shin, foot and point, but it appears the point was designed to be bolted on, and I...

Hi im looking to put wider wheels and tyres on my 10 series to reduce compaction, does anyone know what other makes use the same wheel fitment. Mine is a series 3 7810. Thanks

Hi, I recently pxd my 7610 Q for a 7810 SQ, but after resolving a lot of the previous bodge work and seized up levers etc I've noticed the pto is constantly spinning, I removed the quadrant controls as all the levers were seized up, could one of the controls linkages have become unlinked in the...

recently bought this ford 7810 and trying to get wiring right so basics work. Ironically all but one workmlights are working. But no headlights at all and I know the lights themselves work and are connected. But found his hidden away, any idea what relay or relays are missing?q1a1q

recently bought this ford 7810 and trying to get wiring right so basics work. Ironically all but one workmlights are working. But no headlights at all and I know the lights themselves work and are connected. But found his hidden away, any idea what relay or relays are missing?

hi as the title says I'm after a complete rear window for a 7810 7610 super q. I had one ordered from a guy in Ireland then he cancelled on me. Apparently courier wouldn't insure it.

hi does anyone know the specs for a quicke 560 loader please?

Hi All, me again, search as I might i cannot find a definitive guide to fitting a powerstar 4 or 6 cylinder into a ten series, i would like to know obstacles and cures please. To try and keep this on topic...? I've read the fors and against, so I have formed my opinion of what I would like to...

Hi All, me again, search as I might i cannot find a definitive guide to fitting a powerstar 4 or 6 cylinder into a ten series, i would like to know obstacles and cures please. To try and keep this on topic...? I've read the fors and against, so I have formed my opinion of what I would like to...

hi, I'm looking to check the boost on my 7610, I've removed the blanking plug in the test port, but from what i can tell the plug size is 3/8 with a 28 tpi thread, unless its m10 with 0.9 thread, but due to its age I imagine it was not intended to be metric. So does anyone know for definite the...

Hi me again, after parking, or trying to park my new tractor (ford 7610 b reg 1985) on a hill the other day, and it not stay there, luckily I checked the hold before jumping out. I examined the handbrake cable, its a bit frayed so needs a new one, but I see there are holes on the mechanism, and...

Hi guys, I'm new to the forum, I have recently purchased a little old ford 7610 with a farmhand f12 mk2 hydraukic loader, but although it seems to work fine, when I tried to lift a 1000l of water in a water bowser it didnt manage it. I thought it should lift at least a tonne, its plugged into...