Search results

  1. E

    Jcb TM310 boom not extending

    Hi David I don't think so, when I finally got it into calibration mode the boom comes right out, but it won't finish the calibration. Many thanks!
  2. E

    Jcb TM310 boom not extending

    Hi All Got a tm310, the boom only extends about a meter but no further, comes back in fine. You can hear the Hydraulics cutting out when it stops, so it's not deadening etc. Any pointers? Thanks
  3. E

    MANITOU MLT 627 BRAKES BINDING

    Hi all, having trouble with an mlt 627 2012, mainly when the machine gets warmed up the brakes bind on, they bind on more when turning, We've stripped the front axle down and can't see anything major wrong, the discs are in good order and the handbrake levers are free. We are hoping it's just...
  4. E

    Claas dominator 105 hydrostat problem

    What was this in the end thanks!
  5. E

    Manitou MLT627T boom fault help!!!

    Thanks ACE much appreciated, I'll have a go later on!
  6. E

    Manitou MLT627T boom fault help!!!

    Hi all, got a 2012 MLT 627 TURBO, when trying to boom out the boom only moves out around 1 ft at a time before stopping, then you have to let go of the roller switch and re-press to get it to go another foot etc. etc. The boom pulls in fine no problems at all, and if you lower the boom whilst...
  7. E

    Mf 8925 shuttle problems

    Hi Steve I'm not sure on the heat sensor but some machines go off the coolant temp sensor usually on the cylinder head of the engine. I could be wrong though, thanks!!
  8. E

    caterpillar th220b

    Did you get this sorted in the end buddy, we have one doing the same, many thanks!
  9. E

    Cat th220B no boom functions

    Hi All we have a cat th220B which has lost its boom (joystick functions) red exclamation light flashing on the dash. It did this a couple months back and we bypassed the hydro/joystick cut off switch in the rear right hand corner. It worked for a while but has since stopped again, Does anyone...
  10. E

    Manitou telescoping boom fault!!! Please help

    Hi Martin I'm not fully sure but fairly positive that you have to take at least 1 boom section out to do the pipes, if you can get boom right back in you can pull put the first telescope ram from the backend
  11. E

    Manitou telescoping boom fault!!! Please help

    Hi Martin not yet, so far we think the solenoids, joystick etc. Seem to be ok, going to have another go Monday. Have you done much to your machine? Thanks
  12. E

    Manitou telescoping boom fault!!! Please help

    Hi all we currently have a manitou mt1840 in. Telescope boom won't go out, if I swap plugs on solenoids it goes out and won't come in BUT when the plugs are put right it still doesn't come in. Also when the boom out switch is worked the joystick disable light comes on. Stripped joystick all...
  13. E

    Manitou JSM joystick

    Did you get this sorted bud? We have a one with the boom in and out playing up (similar issue) cheers!
  14. E

    Manitou 741 no gauges

    Did you sort this in the end mate we have one doing exactly the same. Thanks!
  15. E

    merlo 40.7 turbofarmer issues

    Hi there, thanks again for your help. Would you happen to know where the switch inside the boom is? Many thanks
  16. E

    merlo 40.7 turbofarmer issues

    Hi there thanks very much for that, I'll have a look. Would you happen to know where the slow decent valve is? Cheers!
  17. E

    merlo 40.7 turbofarmer issues

    I all, weve got a 2009 merlo 40.7 turbofarmer, the boom is very slow to come down, all other functions work fine. Im thinking check valve but is there anything else to check before i look at it. i must add that the load monitor had never worked whilst theyve had the machine so i dont think its...
  18. E

    Mf 8925 shuttle problems

    Hi Chris, ours was the transmission ecu, it was £1800 but got it away.
  19. E

    New holland tx32 concave removal Please help...

    Hi all can anyone can anyone guide us in the right dircetion of how to take the concave out of our tx32, we have trunken off, all bolts out etc. but its being held in by the de - awning plate handles, is there an easy way to remove them? many thanks
  20. E

    Jcb tm 310 low on power

    Hi all we currently have a 2009 jcb tm310, it is slowly getting more sluggish on the road, it is now very gutless to the point where it cant get to 6th on a very slight slope. It is a 6 speed machine, all gears work fine and it doesnt seem to be binding in any way as it rolls freely in...
Top