Search results

  1. E

    Jcb TM310 boom not extending

    Hi All Got a tm310, the boom only extends about a meter but no further, comes back in fine. You can hear the Hydraulics cutting out when it stops, so it's not deadening etc. Any pointers? Thanks
  2. E

    MANITOU MLT 627 BRAKES BINDING

    Hi all, having trouble with an mlt 627 2012, mainly when the machine gets warmed up the brakes bind on, they bind on more when turning, We've stripped the front axle down and can't see anything major wrong, the discs are in good order and the handbrake levers are free. We are hoping it's just...
  3. E

    Manitou MLT627T boom fault help!!!

    Hi all, got a 2012 MLT 627 TURBO, when trying to boom out the boom only moves out around 1 ft at a time before stopping, then you have to let go of the roller switch and re-press to get it to go another foot etc. etc. The boom pulls in fine no problems at all, and if you lower the boom whilst...
  4. E

    Cat th220B no boom functions

    Hi All we have a cat th220B which has lost its boom (joystick functions) red exclamation light flashing on the dash. It did this a couple months back and we bypassed the hydro/joystick cut off switch in the rear right hand corner. It worked for a while but has since stopped again, Does anyone...
  5. E

    Manitou telescoping boom fault!!! Please help

    Hi all we currently have a manitou mt1840 in. Telescope boom won't go out, if I swap plugs on solenoids it goes out and won't come in BUT when the plugs are put right it still doesn't come in. Also when the boom out switch is worked the joystick disable light comes on. Stripped joystick all...
  6. E

    merlo 40.7 turbofarmer issues

    I all, weve got a 2009 merlo 40.7 turbofarmer, the boom is very slow to come down, all other functions work fine. Im thinking check valve but is there anything else to check before i look at it. i must add that the load monitor had never worked whilst theyve had the machine so i dont think its...
  7. E

    New holland tx32 concave removal Please help...

    Hi all can anyone can anyone guide us in the right dircetion of how to take the concave out of our tx32, we have trunken off, all bolts out etc. but its being held in by the de - awning plate handles, is there an easy way to remove them? many thanks
  8. E

    Jcb tm 310 low on power

    Hi all we currently have a 2009 jcb tm310, it is slowly getting more sluggish on the road, it is now very gutless to the point where it cant get to 6th on a very slight slope. It is a 6 speed machine, all gears work fine and it doesnt seem to be binding in any way as it rolls freely in...
  9. E

    John deere 2140 gearbox strip HELP

    Hi all we are trying to strip our john deere 2140, we have split at the back between the two gearboxes, something has failed behind the input housing (like picture attached) to the back section but we can't seen to get the input housing off, it seems to be stuck on the selector rails, we know...
  10. E

    Case 956xl torques

    Hi all could anyone advise me the engine torque settings for a case 956xl Mainly head bolts and big end bolts. Much appreciated
  11. E

    Jcb 535-60 Gearbox issue

    Hi all, we have a JCB 535-60 load-all at the moment. it is 1,2,3,auto on the f/r lever, is this a 4 speed transmission? It has an issue where it will not set off in 3rd gear (gear doesn't select at all, engine just revs), when put into auto it will set off fine but once it reaches full speed it...
  12. E

    Jcb 525-60 boom/3rd service

    Hi all, we have a 2004 Load-all 525-60, the fuse for the telescoping boom/3rd service keeps blowing, i think i have traced this back to the solenoid which switches the 3rd service from the head-stock to the PUH as the solenoid was really hot even heating the wires going to it. I have unplugged...
  13. E

    McCormick ground speed sensor

    Hi all, i've got a Mcormick CX105 Xtrashift, the ground speed is not reading on the dash, the display just stays at 0.0 mph. The dash is not the issue and we are getting the correct powers/earths to the correct pins up to the dash, so i believe it is the ground speed sensor its self. could...
  14. E

    JCB 535-60 JUMPING OUT OF 3RD GEAR

    Hi all, we have a JCB 536-60, when travelling on the road every 10 seconds or so just jumps back down to 2nd gear from 3rd, does it regardless of weather or not it is in auto. any help would be very much appreciated.
  15. E

    Case mx200 transmission fault.

    Hi all, we have a case mx200, it has no steering and wont drive at all. It occasionally takes up drive for 3 or 4 feet then jumps back out. No low pressure lights on dash or anything.
  16. E

    manitou mt 625 not driving

    hi all, i have an issue with my manitou 625, it will not go forwards or reverse, hydraulics will not move unless the parachute button is pressed and the rev counter is not working. the alternator is charging good at 14.6 volts (could this be too much) all wiring checked so far looks ok, the...
Top