Search results

  1. G

    Changing JCB service interval figure

    Service interval is set at 100 hrs on our 535.95. Have worked out how to zero the service reminder, but not how to change the interval. Any ideas ? 🤔
  2. G

    New Holland error code

    Obviously something to do with the armrest console, any ideas ? 🙄
  3. G

    Nexat gantry system

    Have been seeing this on various social media platforms for a while, finally got round to watching some of it. Is there any mileage in this sort of thing for large acreage areas, or is it another concept that will eventually be consigned to the history books ?
  4. G

    Straightening threaded bar

    Got a Fergy steady bar that needs some attention, is it possible to heat and straighten threaded bar successfully, or am I wasting my time 🙄
  5. G

    Trimble XCN 1050 problems

    We have a Trimble XCN 1050 set up fitted to a JD 6830, predominantly used for spraying. It picks up and follows an A/B line for so long, then seems to drift slightly then give the wheel a handful to get back on line, causing it to oversteer the other way, ending up with it swerving from side to...
  6. G

    New Holland T7 dashboard settings

    Came across this while looking for error codes, anybody know what SWCD stands for, and whether it should be set on yes or no ? I’m not sure if I changed it while I was messing about 🙄
  7. G

    New Holland autosteer

    When recording a boundary, where is the record point ? The dome, the leading edge, or trailing edge of the implement ? Am getting some funny shaped corners and wondering how to improve the job
  8. G

    Do combine rotor losses actually exist in OSR

    Bearing in mind how easily it knocks out, by the time 30ft of fit OSR has gone up the feeder and through a 25-30mm concave gap, do rotor losses really exist or is it mostly reading bits of pod and trash ? 🤔
  9. G

    NH T7 AutoCommand, 50k box only doing 40k

    Seems to be restricting itself, Forward speed maxed out on the scroll wheel, engine droop maxed out, pedal to the metal, but only doing 40k Done a gearbox recalibration, which made no difference Anybody had this before ?
  10. G

    Is anyone still buying side by side 12 bores ?

    My dad has a side by side 12 bore that he bought back in the 80’s, it’s been in a sleeve in the gun cabinet ever since and never had a cartridge through it. He seems to think it ought to be worth a bob or two, I think he might be disappointed 🙄
  11. G

    Prospective pay rise

    Always been paid based on a 39 hr week plus o/t at time and a half. This time I have been offered a choice of a rise carrying on with the same set up , or a higher basic figure plus 1.4 o/t. Based on my average annual o/t hours, there’s only £140 difference in my gross earnings. It’s set me...
  12. G

    New Holland Intelliturn

    Got a 10 day demo of Intelliturn, not quite got to grips with it yet. Anyone out there using it and got any experience to share ?
  13. G

    NH T7 Cross shaft leak

    Noticed the cross shaft dripping oil yesterday. Is it going to be expensive or is there a seal in there that might be to blame ?
  14. G

    RDS Artemis control box

    Have got 3 metering units running through one box, apparently each can be assigned a name, would like to change the third one to pellets but the book doesn’t tell you how. Anyone done it before
  15. G

    NH combine cab fan

    Not even sure what its proper name is, but there is a fan below the cab filter housing on our CR, that comes on with the ignition. One of the wires had come off at the spade connector, plugged it back on but it didn’t come to life, so i’m now suspecting a fuse. Anyone know what name it would...
  16. G

    Hydraulic top link marker

    The top link on our T7 has no marker sticker ............or a pointer, come to that. Is such a thing available ? as i’ve had a google round and drawn a blank
  17. G

    Vaderstad seed rate

    Is there a way to get the seed rate to react quicker to forward speed increase. As you set off from the end with ours it takes a couple of seconds/few yards for the seed rate to keep up
  18. G

    New Holland spool valves

    The spool valve buttons on our T7 controller have scv 1 on the vertical buttons and scv 5 on the horizontal as default. They can be changed in the reconfigure screen on the monitor but then you get this annoying reminder every time you lift your ar$e off the seat Is there any way to change the...
  19. G

    Kuhn spreader settings

    Got to spread some Origin 0-17-19-2.5 next week. Have looked on the app and online but can't find any info anywhere. Anyone on here ever put any through a Kuhn 30.1 that could save me a bit of guess work ? :rolleyes:
  20. G

    Freeflow return port on T7

    Need to fit a 1” female return coupling on a T7.315, which is the best port to use ? There is one on the top behind the top link but it looks too close to the top link for my liking
Top