Got a 6400 in with what would appear to be clutch slip in the higher gears, when this happens the engine remains under load. The transmission is all manual, no electronic powershifts. So that leaves the hytrol unit or the dry plate clutch. Tractor has only done 3100 hrs. I beleive the hytrol...
The cut and hold on the right hand side is not cutting. The ram wont go down the last two inches to get the wrap cutting on the knife just ends up braking when the bale goes off the back.
Have tried bleading air from the ram and made no difference. Would the accumulators be at fault but from...
Jd 6150r autopower. wouldnt release the trailer brakes at all. Have replaced the park brake solenoid they now work but are slow to release. At a junction for example you come off the brakes and the trailer is holding back for a few seconds as the yellow line pressure is released. Anyone...
Hi looking for some pointers as to where to start with this. The handbrake is releasing as normal but the light and the buzzer stay on. This is on a 2002 3185. Is the light activated by an air pressure switch or in the handbrake leaver itself.
regards
Mark
Any pointers on getting rid of the flashing spanner. Havent had any joy in the manual, seem to remember it being a simple combination of buttons but its been about 5 years since i last worked on one!
Thanks in advance
Mark
Recently acquired a medium sized parts washer. Cant find any clear cut advice as to what fluid to put in it. Most degreasers seem to be water based and im not sure if thats the right thing for something thats reused.
Will be needing 30ish litres i rekon.
Lets see what we can come up with!
Evening,
Having problems with a 6920 not starting its 2002 so pre common rail.
Lift pump on-top of filter isnt running, no power to it although the fuse is good. Any pointers on where to look next.
Regards
Mark
I’ve got a 8050 which we’ve recently rebuilt the engine on including recon fuel pump and injectors.
It has a slight hint of white/grey smoke when running this stops when cracking injector number 3 and the exhaust is clean. Removed the injector and swapped with number 4, the problem did not...
Got a Dx140 here at the minute and got in it this morning to find the screen like this looking like a Microsoft desktop. Machine works as normal. Just no gauges etc
Thanks in advance
Mark
Im looking to get a speed signal from the tractor for and electric air seeder we have fitted to our power harrow. The 18plate valtra n134 hasn’t got the round plug pictured below but has got the rectangular output on the topcon.
Is there an easy way around this as manufacture is suggesting...
Got a friends mini digger in with fuel starvation issues which can be cured by blowing fuel lines back to tank every 2-3 hrs. All roads point to a blockage of the pickup pipe. The machine runs better when the tank is at least two thirds full. Also pointing to pickup pipe.
Filters are recent...
The linkage fails to operate when the internal or external cab buttons are used.
Pressing the end of the solenoids however has the linkage working like normal.
Has anyone any experience of these tractors. Wondering if there’s a calibration sequence or something to do?
Thanks in advantage
Mark
Just setting up a new wheel bearing after changing the hub seals. I’m looking for the torque setting for the wheel bearing bolts. I’ve ordered a workshop manual but it still hasn’t turned up. I believe it’s a Carraro axel
Regards
Mark
Looking for some rear packer bearings. Bearing supplier doesn't do them for the rear as they have a heavy duty casting.
Getting astronomical prices for genuine simba, has anyone found and alternative. It's a 62mm bore and uses m12 bolts to fix it to the frame.
Thanks in advance
Mark
Got a 10plate 526 with about 3.5k hours which has done its fair share of towing. It's slipping in 3rd gear and everything points to a clutch pack at fault either seals or plates. No significant debris found in the filter or screen when changed this week.
Is there anyone other than main dealer...
Contractor I work for is looking at getting auto steer gps and we've had a lot of conflicting advice. It will be used predominantly for mowing with triples and maize drilling 6row with section control on the drill. Will also be used for fertilising and cultivating but not as much.
The main...
Does anyone know of a pattern replacement? Struggeling to find anything on the net other than componant parts for one. Thought it would be easier to do a complete replacement rather than rebuild the old one.
I've recently purchased this tractor from a customer of mine. It seemed like a good idea at the time [emoji85]. The linkage will only work on the outside buttons and the set of buttons similar to those on the mudguards but inside at the back of the cab. Not on the armrest rocker or the position...
Hi has anyone got a login to this site got about 5 items I would like rough prices for would just like a rough idea of the cost so I know weather to persevere or not. Have emailed them for a quote but not holding my breath.
Regards Mark
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.