Search results

  1. Curt

    Grimme SV 260 potato harvesting

    Very, some of our land is on peat which can be soft even in good conditions. Travels very well on 1000/50 r25 tyres. Alot further then the GZ we had before and making alot less mess, would go places you wouldn't take a trailer when wet. Wheel motors on that are alot bigger than a GZ/GT aswell...
  2. Curt

    Case Quadtrack

    After owning an stx 375 I'd say get the older 93 series steiger version. Before buying I read an article stating gearboxes tended to have a 6000 hour life span and engines around 8000 before needing work. Rebuilt the gearbox in ours at 5800 hours and engine had 10k spent on at 8200 hours. Got...
  3. Curt

    JCB Joystick button switches

    Do you know if a 2013 JCB 541-70 would be a 2wire or 4wire switch? Thanks
  4. Curt

    Nh seat/handbrake error

    Have you done a h9 test for the switch to see what readings it is giving?
  5. Curt

    Nh seat/handbrake error

    Check wiring under the seat, had similar problem and was a wire inside conduit that had become trapped and damaged by the seat moving.
  6. Curt

    T7.210 case 160 front pto clutch pack

    M J Robinson can supply them for around 1200
  7. Curt

    T7.210 case 160 front pto clutch pack

    Gone through 2 this year, looking at replacing with a degenhart front pto kit instead. Has anyone any feedback on the degenhart stuff?
  8. Curt

    NH Intellisense worth it?

    Had a demo of it last year on a 9.90. don't know how much extra it is but the next combine will definitely be having it. My brother drove it with very little combining experience and achieved more output and less losses then 2 other fairly experienced drivers that ran it without. 👍
  9. Curt

    claas challenger 55

    Check condition of the drive wheels if they're fairly worn it'll be next to useless in the wet
  10. Curt

    Clayson/New Holland Parts

    Having a clear out of some old combine spares in the workshop. Mainly tx 68 parts but some 8080 and 1500 series. Will keep updating with pictures. if anyone sees anything and wants some better pictures or parts numbers let me know 2 boxes of new fingers and many boxes of new chopper blades on...
  11. Curt

    How to form steel packer rings?

    This was a photo I found on the Internet where someone had refurbished the packomat, each half of the ring is 4 sections then welded at the top to form the v Not doing it to save money, I'm not refurbishing a packomat just trying to create something with a similar profile of ring and was...
  12. Curt

    How to form steel packer rings?

    Does anyone have any ideas how to form the rings like this? Have access to a cnc plasma to cut the sections and have our own rolls and pressbrake. Just can't think how to get them to form a v shape. Was hoping someone might have some knowledge before I go experimenting. Thanks
  13. Curt

    Reliable Hot pressure washer?

    Had a 3 phase nixon for about 15 years. Been a good washer and have replaced the original Pump, motor and heating coil over the past 18 months, was impressed we could still get the parts off them and next day too 👍
  14. Curt

    New Holland clayson

    I'll send you some this week 👍
  15. Curt

    New Holland clayson

    Might have a complete header, is south west Lancashire to far for you?
  16. Curt

    Forschritt swather. Anyone got one?

    Ahh yeah yours does look different. Hope it all goes to plan and works for you 👍🙂
  17. Curt

    Forschritt swather. Anyone got one?

    @Dave W this one is just mounted at one end
  18. Curt

    Forschritt swather. Anyone got one?

    I'll get some pictures in the morning 👍
  19. Curt

    Forschritt swather. Anyone got one?

    Ahh good 👍 from Southport, Lancashire.
Top