Search results

Self employed GFW looking for some extra work through the winter months, will turn my hand to most things, doesn't necessarily have to be farm work. Experience in tractor and machinery, cattle, cropping , digger work, drainage and also some building experience. Based in westhill, but happy...

Came across this on Facebook. Thought it might be of interest to a few on here. Pity our current government don't value food security so highly.

Keep getting this message flash up Had a look under spreader but can see any plugs to take apart to check without taking boxes etc to bits , doesn't seem to be counting the area properly assume it's to do with this error too ? Anyone had this before and found the problem?

Possibly got a 2.5 ton digger coming from fortwilliam beginning of next week, anyone heading back from that direction with a bit of space or looking for a return load ? Would be coming to AB32 area but can pick up from elsewhere if it suits.

Been asked if I'd sell my old major but not sure what it's worth in its current state It runs and works but needs a fair bit to get it right Needs New exhaust Wiring loom Rear wings The back 2 wheels rims don't match It's had a replacement engine at some point and it no longer starts off the...

We've acquired a couple drums of the following oils and I'm trying to work out if they'd be usable in the gearboxes on the balers, or for anything else front hubs etc, don't want to go using it and find out it's going to do more harm than good. Also 80/90 specs to compare as that's what...

Been offered one of these fail safe engine control units in the picture below, problem is I can't find a wiring diagram for it. Anyone happen to have a diagram or know of a link etc to one Cheers in advance (y)

Just a warning to anyone with a 6000 /6005 series deutz about the engine fan coming apart from the water pump. Was baling this morning and thought I smelt something burning, had a good look round tractor and baler and couldn't find anything ... started off again and within a couple minutes...

Hi, Got a question about the blue wire on the 7 pin plug on our deutz tractors, the tractors are a M 620 and a 6160.4. I'm thinking of putting reversing lights on a few of our trailers and would like to use the blue wire to power the lights rather than put in an extra cable and plug for the...

Anyone know of a usable 800 r32 combine tyre in Aberdeenshire ? Thanks Mike (y)

Got a bag of spare bits in the toolbox for the baler but don't know what their for or where they go, or if they even belong to the baler. any one know ? Had a look in the manual but couldn't find anything. Cheers in advance (y)

Seem there quite a few folk on here who have something to do with earth works or construction, so though it might be an Idea to have somewhere to post pictures of the work you do and somewhere for general chat. So let's see your work or maybe something you've came across on your travels, the...

The 4wd stopped working today on my m620, sometimes works sometimes doesnt (had suspicions for a week or so), no fault codes and the 4wd light is on when it should be. when i got the tractor the solinoid wasnt working and had to be replaced, question is would this be the problem again? I...

Hi,Does anyone know where to get bushes for the shaker arms that are attached to the seives apart from the dealer, ordered from them earlier in the week and they have put out the wrong parts ( yet again :mad:) Have searched on kramp website and a few in the states but came up blank. Any...

The clips in the photo are to hold the splitter gear solinoides in, and as u can see they keep breaking (4th time in 6 months) just wondering if anyone has this problem or if it's something wrong with the tractor. TIA.

My uncle has a leyland and on the tin work it has 255 but on the badge on the chassis it is a 344, was wondering if there is a way to tell which it is?

Hi, having trouble with above tractor lagging in power for a while now so couple weeks ago changed the 2 fuel filters and the 2 backend filter along with new oil in backend and engine. filter were genuine filter and has made no differece to the preformace. the engine is runnig smooth and is...

suspentions went down in the air bags but dont seem to be burst, iv took off the arm off of the control valve and moved it up and down no air goes to the bags but u can hear air coming out. anyone had this before. any help would be much appreciated.