Search results

  1. E

    Best make of mig welder

    bought a oxford 300A single phase , new in 2020 as an upgrade to my R-tech 250A . After around 2 months the motor that feeds the mig wire coil out out stopped first , the dealer told me they had bought from a different supplier and there was an issue , they sent me out a new motor and away...
  2. E

    New Oxford welder

    I bought a oxford 301 single phase , new in 2020 as an upgrade to my R-tech 250A . After around 2 months the motor that feeds the mig wire coil out out stopped first , the dealer told me they had bought from a different supplier and there was an issue , they sent me out a new motor and away...
  3. E

    MF390 rattles under acceleration

    no , has the Hi Line Cab
  4. E

    MF390 rattles under acceleration

    yea , the front drive shaft is up the side off the engine
  5. E

    MF390 rattles under acceleration

    We have a 1989 MF 390 when you accelerate in either low or high forth gear it develops a bad rattle in the gearbox / back end area, any ideas where to start
  6. E

    Sawdust

    Where could i get a full load of baled sawdust?
  7. E

    Max span

    standard 6 meter bays
  8. E

    Max span

    I can get some 457 x 152 x 52 beans @ 9 meters long , if I was to use these as uprights for straw shed uprights what span could I get away with , will be using galvanized purlin and 0.7 single skin roof sheeting using 150mms concrete panels for the first 2.4 m at the base
  9. E

    baler driver

    There's zero big square baling contractors here in my part of Ireland... 100s of round balers
  10. E

    baler driver

    anyone needing a baler driver for the harvest very mature 19 year old looking experience with a large contractor in square baling this harvest, has six years experience round baleing, mowing, tedding, raking carting grass etc, well trained at preventative maintenance and fairly able in...
  11. E

    Purlins

    Any 6 meter 7 inch C purlins for sale need around 120
  12. E

    Steel frame shed

    How much is it?
  13. E

    Purlin spacing

    All ours at least 1500 spacing but I seen one yesterday at 1800
  14. E

    Purlin spacing

    Putting up a new shed, 20 m span 6 m bays 18 degree pitch and using 0.7mm Plastisol sheeting, going with 175x65x1.6mm purlins, what's the max spacing between purlins?
  15. E

    Lincoln to Dublin

    I could do that £250 for both including the customs paperwork 07927955778 or [email protected] we are based in Newry
  16. E

    Silage / Straw / Hay Price Tracker

    Bales from the south will weigh far less than a english bale, anywhere between 250kg to 360kg over here 8x4x4 are only really popular about Louth and North Dublin they weigh around 400-430kg I can deliver you a load at £47 😊
  17. E

    Electric motor for driving a baler

    Im surprised you can get a 10hp motor on single phase, I thought 5hp would be the max, it must have some type of star delta type starter
  18. E

    JCB teletruk price

    Anyone got a price for a new JCB teletruk, thinking of buying a 35 model 4x4 rang two dealers on different occasions but never heard back from them I see you can buy direct from JCB on there site but maybe its just for smaller mini diggers / dumpers
  19. E

    Electric motor for driving a baler

    Probably at 50KW, It would probably be easier on power to use a hydraulic motor and feed it from a hydraulic pump
  20. E

    Diy concrete panels?

    We collected crushed concrete from a recycling place and they had been doing panels took in from a council salt yard, they just had like A252 mesh in them, those prestressed ones would be most likely for upper floors in houses, shuttered walls arent prestressed, most don't even have steel in...
Top