Search results

I usually flail mow some roughing industrial land approx 40acres. I haven’t done it for a couple of years and now they are asking if I can do it and collect the grass to be disposed of on site. (Presume it is to promote wild flowers etc). I wouldn’t like to mow it with a normal mowing machine...

Original tyres are getting hard to source and I think these will fit. Seem reasonably priced but not heard of tvs eurogrip tyres before. Anyone had any experience with them? Trailer isn’t used much so worth a punt?

Just trying to see if this alternator works off a dead machine as I got a job for it. Looking to bench test it but not sure which wire do what. I know the bat terminal goes to +be on batery and earth but what about the terminal in the plug and the little fly wire coming out of alternator. Any...

Hi Looking for a 4 ton tracked dumper unit to be moved from BA22 8TD to LL12 0TH. It’s just the tracked unit without the knocker on. Available to collect immediately. Thanks

Trying to take a beacon off the roof and need to get the access panel off. The usual nothing goes to plans and can’t get the screws out . What is best way to get these screws out on Tm150. Some one has been at them before me and rounded them off and the other won’t budge. Thinking of welding a...

Trying to take a beacon off the roof and need to get the access panel off. The usual nothing goes to plans and can’t get the screws out . What is best way to get these screws out on Tm150. Some one has been at them before me and rounded them off and the other won’t budge. Thinking of welding a...

Called in to have a couple of 1 inch pipes about 2ft long made up to replace a burst pipe on the hedge cutter. Took the old pipes and he made them up while I waited so good service. I wasn’t in a rush so would have collected next day if required but they had nothing else to do so made them while...

Hi, I have noticed the back end on the t6010 getting very hot. Today when I brought it back to the yard after pulling low loader with 6ton digger on for 40 minutes up and down a few hills so it was working it hard. I noticed the back end was bone dry even though it was raining. Putting my hand...

Hi As per the title. I am after some advice from the knowledgeable people off the forum. Yesterday morning the Transmission low pressure warning symbol came on about 15 seconds after starting the tractor. I turned the tractor off and restarted and in never came back on. I used the tractor for...

Hi all. I have just finished sheeting my machinery shed and just the barge board flashings to put on. Do You overlap them or but up. The flashing edges are bent over so not to be as sharp but will this stop them sitting properly? Any advice appreciated.

Hi guys. I know there are some very knowledgeable hydraulic chaps on this forum so thought i would ask if you can help. Have got this enerpac connected on the back of a milling machine to operate a clamp and it use to build up to certain pressure then just stop. Now it appears to be pumping...

Hi all I have just noticed that the pto is turning when it is not switched on. I noticed it last week and today it was showing the speed when its not engaged? I have tried to stop it by hand but it wont. Any advise much appreciated.

Hi guys i have just tried the log splitter and the cylinder wouldn’t retract. It felt like the handle was stuck. I strippped the valve down and couldn’t see anything obvious but it won’t work at all now. I am not quite sure what the bit I have circled red does? I am unsure if I have put it back...

Hi all. i have just bought a 6ton doosan dx 62 digger and It’s showing password error. It appears the machine has had a 4 digit code at some point but nobody knows what It is. Dealer is looking at a fortune to come out and reset it. Don’t suppose there is someone on the forum who knows how to...

Looking for a price and availability to move a 6ton digger from Manchester to Wrexham. Wouldn’t be till late next week but depending on current circumstances. Cheers

I have just bought a herbst mini low loader (10 ton 18ft long ). The paint work is scabby but the floor is chequer plate and good. What would a rough idea of price be to get it sand blasted or do i just wire brush and paint.? Also does anyone know RAL code for herbst red paint. thanks in advane

Have just noticed the rear light and indicator lights have longitudinal crack in them between the clear part and the coloured part. Has anyone else had this problem, seems strange that both have done the same. I have priced the lens from local new holland dealer at £36 and have just noticed on...

Has anyone got a dewalt grease gun? I have just ordered one and hope I have done the correct thing. I have got all dewalt stuff so made sense regarding batteries etc but they are quite a bit more expensive than the Milwaukee that a lot of people seem to have. I have bought it from America via...

I have got one of these 3 pin plugs on the back of the tractor. I want to power a flashing light for the trailer off it but what pins are positive and negative? Why are there 3 pins? The tractor is a new holland t6010

I have just noticed our t6010 is dripping oil from the where the 4 wheel prop shaft goes into the rear gear box. I am quite handy with the spanner but how difficult is it to replace the oil seal and is it a new holland part or can I get one from my normal bearing supplier? Will I have to drain...