Search results

  1. G

    Reekie ridger

    Scanstone would be worth asking depending on age will be same shape board's
  2. G

    Trelleborg tyres very disappointed

    Had another 540 65 30 trelleborg crack behind the lugs the other day had the same problem few years ago on another tractor rep said never seen it before. But the tyre's are made in several different factory's the one I took off had made in Italy on it where as the one I put on had nothing...
  3. G

    Amatron 3 power source.

    You can buy the isobus plugs that fit into the socket on your tractor and just fit onto the power supply for the control box. I have them on balers and not had any problems also run an amazone drill running two electric feedrollers. Makes swapping tractors easy.
  4. G

    Amatron 3 power source.

    Plug it into the isobus socket. That way you can swap it to any tractor with ease. Have used Anderson sockets in the past after a while was getting bother with bad connections due to corrosion.
  5. G

    Loading and transporting bales

  6. G

    Fendt stabilisers

    What year is your 716 upto 2011 I think will be smaller pin diameters than a 720. If its the threaded ends thats worn you can buy replacement weld on ends or make your own
  7. G

    Tractor/trailer brakes.

    I had this issue. If you adjusted load sensing on trailer to get them to work correctly on new tractor it was unusable on older tractor as would just lock the wheels solid just slightly braking. Ended up getting the pressure adjusted on new tractor. Heard of a valve been fitted to some that you...
  8. G

    Fendt error code

    Open the flap in the floor and you will see the hex where the manual drive lever goes onto the control motor spray this with wd40 and rotate it with the manual drive handle or a socket to free it off its probably seized .
  9. G

    2006 fendt 818.

    Can you re activate cruise when it drops out or does a symbol come up on dash .Try holding the clutch pedal up with your foot if this cures it you need to calibrate clutch pedal
  10. G

    Contractor near dundee

    Probably already done the job but if not try black environmental service's they have tankers and not far from Dundee
  11. G

    MF 3065 lift problem

    Could you swap the lift panel with the 3095 to see if the fault moves
  12. G

    MF 3065 lift problem

    Have you checked the bolts on the end of the cross shaft haven't come loose or snapped. But if applying pressure to the depth control knob helps it could be faulty.
  13. G

    Hydraulic motor

    You can get a brake like this to use your existing motor but not any experience of them. A motor with an internal brake isn't the cheapest or certainly wasn't when I priced a replacement for my forager spout.
  14. G

    Hydraulic joystick for backend

    Is the spools on your tractor cable controlled or linkages direct to your spool valve. You can get a joystick with cables and a button to operate your diverter but whether you could connect the cables to your existing spool valves I'm not sure. You could fit a separate spool block like for a...
  15. G

    Hydraulic joystick for backend

    You could have a manual valve that you reach out the back window and move the lever over if it's only occasionally used or an electric operated one that you would need to wire up and supply power too through a switch in the cab . Look on flowfits website for different options and price's maybe...
  16. G

    Hydraulic joystick for backend

    Yes you could get an electric diverter valve and have switch in the cab. would the single acting spool operate the raise lower or do you need to power it down aswell.
  17. G

    Hydraulic joystick for backend

    How many spool valves does the shear grab need and how many does the tractor have .could you do away with the valves on the shear grab and plug the pipes direct into the tractor spool.
  18. G

    Air gun to air seat

    Some fendts with evolution seat the air is supplied from the tractors air system
  19. G

    Audi s3 quattro in snow/climbing an incline question .

    The s3 I had was brilliant in the snow. did have a set of winter wheels and tyre's on it. Low profile tyre's are hopeless.
  20. G

    716 cab heater

    I used a block and tackle .this is when I was changing a leaking heater matrix on a 714.but I had cab tiping brackets. Not sure if you you could just gently lift the back up a few inches if you would get enough room. There is two bolt holes in the bar below the back window to attach lifting...
Top