Search results

  1. MF-ANDY

    JD 7920

    Anyone got any tips on changing the bearing assembly for the engine fan. @Phil P
  2. MF-ANDY

    Liftomatic on new Holland

    Have one where the plastic lever won't stay in so machine is always lifting out of work. Guessing something is worn but how do I get to it.
  3. MF-ANDY

    Lexion 550

    Are these bolts holding the rubbers on, screwed into captive nuts? It doesn't look like they are
  4. MF-ANDY

    Phiber bale accumulator.

    Phiber ac3104. Has anybody got any experience with these machines. I have one that isn't sequencing correctly. Tia.
  5. MF-ANDY

    Sky glass

    Anybody got it and any experience with it?
  6. MF-ANDY

    Track tensioners

    Have a pair of tensioners that are being over hauled. A 100mm ram section that is extended with grease. This has a sprung loaded peg that pushes on the front idler and gives it some cushioning. The pistons are going to be skimmed on the outside and chrome or stainless sleeves pressed on. We...
  7. MF-ANDY

    John deere isolator

    Is this genuine a jd kit? This one won't pass current so is temporarily bypassed.
  8. MF-ANDY

    Kverneland NG.S 101 power harrow

    Anyone stripped one? Have one that has two rotors jammed together. Assuming it's teeth off a gear as all other pairs are still timed correctly. Looks like a top off job. Does the gearbox just lift off with a spline or is it a through shaft? Tia.
  9. MF-ANDY

    Horsch pronto

    A second hand one used for first time Friday and again part of Saturday no problems, now stops seeding after a few yards. Stop and start again, does the same, stops after a few yards. Does the same on two tractors. Any ideas before dealer is called.
  10. MF-ANDY

    JD3200

    18 months ago. Overheating, loss of coolant mainly as exhaust vapour, smell of coolant, top hose blown up so obviously suspected head gasket. Head removed, skimmed, pressure tested. Refitted with genuine gaskets and new head studs. Fine until 6 months ago when started needing coolant. Not...
  11. MF-ANDY

    6920 pto

    Customer has a 6920 where the pto has stopped. He says the internal splines have worn away where the pto stub goes in. What sort of job is it to replace this. @Phil P @Tractortech . Tia
  12. MF-ANDY

    Komptech topturn compost turner

    Has anyone any experience with these machines, specifically the tracks. Tia
  13. MF-ANDY

    Job of the day

    Kubota differential bearing
  14. MF-ANDY

    Lexion 550 latch

    Does anyone know what this latch is for behind the battery box of a lexion? 550?
  15. MF-ANDY

    NH CX860

    Lower part of steering column won't hold position. I think The gas strut compresses when the column is pulled back and should hold there until the pedal is depressed which pushes the pin in the end of the ram. This one extends fully pushing the column and wont lock. N H price is extortionate...
  16. MF-ANDY

    JCB 531.70

    Does the box in the picture control the aircon condenser fans? I only have one fan working although both test fine. Got 12v feeding both wires into the box but 12v only comes out of one fan feed wire. Does it run one fan first then two if needed?
  17. MF-ANDY

    JCB 531.70 hand brake cable

    Think I have a broken hand brake cable.Movement at the lever but no resistance all of a sudden. Or are they prone to something breaking inside? What's involved. Looks to be internal at the bottom end. TIA
  18. MF-ANDY

    Alerts

    Why am I getting alerts for threads I haven't subscribed too?
  19. MF-ANDY

    Sliding gate

    Has anyone got any experience of automating a sliding gate? I have been looking at the CAME BK system. Looks to me as though it should be ok for my needs.
  20. MF-ANDY

    3 phase cable

    How deep should it be buried?
Top