Search results

With a NTRIP server you can steram the corrections to a caster like RTK2GO. When configuring the I/O settings of 542 for it you should be able to Enable RTCM corrections. I have a NetR5 but 542 looks pretty much the same. If you want to get the corrections directly from you own base then you...

You can configure the NTRIP server of the Receiver with any web-browser that is in the same LAN. Just dial the IP address of the Receiver to the browser. Please read the manual... I don't use RTK2GO but you will have to create a user account there to use it.

Trimble AgGPS 543 has an in built NTRIP server. You just have to hook the receiver to a 4G router. Ethernet connector is in the multiport connector. So you need: -multiport connector -etehernet cable -4G router with data sim And a user manual...

👍 LOL

What about just drillin couple 5 mm holes on the the top to shake the water out and let it dry for a week an top of the furnace. Then use just some drops of epox clue to fill the holes. But I really do recommend this Beitian from ebay oli Aliexpress. Its is just about 100 -150 + another 10-15...

If your shake test is positive then it is deaf. Might start working if stored on top of a hot furnace for a month or two... I have bought several lower cost Chinese L1/L2 antennas. All of the have worked well and only some have failed after some years. For what they cost they are good and you...

How is the top link in your front 3 point hitch now? Is the implement end of it higher of lower when the tines are in the ground. I would imagine that the implement side should be lower to get more dynamic weight to the tractor front wheels. But this is more like a guess as I do not have much...

Most likely not enough weight on steering front wheels when the tines in front are in the ground.

Yes. The harvester does have a row feeler that works very well keeping the opelwheels on the row. But driving the tractor on the row for 8 - 10 hrs day tor 10 days gets tiring. Even a simple low end steering assist system like this makes it easy as long as it is on RTK. This one fall we had to...

These old Deeres are really bad with tipping trailers. The front hydraulic pump does not get enough oil from the low pressure pump in the gear box. When the small reservoir in the front gets empty of oil the front pump start cavitating. Run it high RPM and tip the trailer in small intervals...

JD 3650 1991 & Thyregod T7 2000. Trimble EZ-Steer on CFX-750 RTK makes work easy and relaxing.

And the scale You are using in calibration process s not wrong?

So yours must be a single hopper drill as hopper is not air tight. So called venturi type injector? And for sure there is no air leaks in wrong places in that system? The seed meter roller in our 4m dual hopper Pronto does not fill properly if there is an air leak in the hopper. If your seed...

Make sure that the seed bin door is air tight. If it is leaking air the seed rate goes down.

Get a SMA to TNC adapter I have used Chinese antennas with Trimble receivers for years. Some have got moisture in, but one can always have a spare one at home as they are low cost. No difference in performance in ag use.

Try to open a field first...

If a rotary injection pump is leaking from the governor lever or stop lever but your tractor starts easy and runs ok I would just change those O-rings. It is not difficult. Most likely you will have the replace the top cover seal also.

The button is for opening up the hood to be able to service air filter. Some of the bigger ones like 3650 have the same button (might be grey) but some have a rubbers straps behind the removable black side screens.

There is a lot of settings for minimum speed, amount etc. but I do not know if they would help you. The jump start works well. Bush it up when U start do drive... I do not now fully understand what is your problem with it.

There is at least the "jump start" on main switch. And might also be flush control behind the left side sprayer icon if I remember right.