Search results

  1. Run to the hills

    Claas mega header

    Ahh yeah if ours had got there think it would be written off
  2. Run to the hills

    Claas mega header

    Not sure, did you put new insides in that hold the retractable fingers ?
  3. Run to the hills

    Claas mega header

    Nope a lump of sandstone, came out the stone trap in bits, still cant believe how it caused so much damage, or why the finger didnt shear like they're supposed to.
  4. Run to the hills

    Claas mega header

    Yep have been through insurance in winter and decision was to get a new one made, however have just found out last week they cant make a new one as some of the parts are obsolete.
  5. Run to the hills

    Claas mega header

    Will a 6 walker one be wider trunking tho? Found a stone that bent a retractable finger and twisted all the shafts and frame inside the auger.
  6. Run to the hills

    Claas mega header

    Have done but they have nothing to fit
  7. Run to the hills

    Claas mega header

    Aye might give them a try, fast running out of options aha.
  8. Run to the hills

    Claas mega header

    Currently on the look out for a header for our claas 204 if anyone happen knows of one kicking about? Or if its possible to make a header from a 6 walker machine fit a 5 walker? Cheers
  9. Run to the hills

    Horstine sprayer issue

    Not sure, could try it and see i guess haha, think i,ll get local agri mechanic out thismornin im no expert on valve blocks and solenoids
  10. Run to the hills

    Horstine sprayer issue

    Yeah am thinking it could be that, think ive checked everything else
  11. Run to the hills

    Horstine sprayer issue

    Ahh no worries cheers, yeah all in right just misbehaving.
  12. Run to the hills

    Horstine sprayer issue

    Afternoon all, cant get any of the boom functions to work on the sprayer, up down fold or tilt. Was working fine last night but today nothing. It ciculates oil fine until you press a switch to move the boom then it makes the tractor work, there is power to all the solenoids and can hear them...
  13. Run to the hills

    Welding a plough

    It's a wonder that pin holds them at all really for the force it gets
  14. Run to the hills

    Welding a plough

    Not sure on age, 4 furrow going on 120hp, looks a good job of a repair, only thing worrying me is that it looks like it hasnt been used since the repair, which i didnt figure out until i got it back and got the headstock off. Ram should hopefully be ok, i straightened the end abit and re welded...
  15. Run to the hills

    Welding a plough

    Yeah most of the ones i know of have snapped at some point, have an older one made by agrolux that has lost many a skimmer.
  16. Run to the hills

    Welding a plough

    Just bought an overum plough that has been snapped and re-welded at the headstock (arrow in 1st pic), just thinking would it be worth adding strength to the shaft it turns on, maybe welding another tube inside the main one, Cheers all.
  17. Run to the hills

    Loaded up and trucking!!

    Nah its ever so old, had a fresh paint job a couple of years ago tho
  18. Run to the hills

    Loaded up and trucking!!

    I did like the scania but for what we're doing cf is spot on, new body on it and rear steer, smooth and comfy, only thing you miss is the extra 110 horses
  19. Run to the hills

    Loaded up and trucking!!

    Bit of a swap r series to a cf
  20. Run to the hills

    Claas mega stopping thresher

    That may be my hope of it being the alternator out the window🤣, off to blow it down now and look for faulty wires. Thanks
Top