Search results

Towards the end of harvest we noticed a crack at the base where it swivels and a little bit of grain leaking out. Presume the long part is separated at the top plus augur - is there a big bearing or simply a seal at the base - does it just lift off - thanks.

800 70 38s on the drilling tractor - looking for a set to give a bit more grip on a couple of banks. Maybe some 710s might do as my tyres are half worn - thanks.

Best tractor on the farm is popping out of drive ( worst when hot ) - would it be a faulty solenoid or the forward / reverse lever - thanks in advance for any replies. Not jumping out of gear .

Looking for an easier way than poking and grinding - my grass seed specialist has a 2metre Sinar but are now over £800 new . Any alternatives please ? TIA

Currently run a MF7726 and a MF8730 which our only ad-blue tractors - 19 & 17 plates. Do we use E9 or 10-40 engine oils? Also in our collection are older tractors such as a Fiat F130 , Case MX170 , T8050 ( basically a Magnum ) , Househam sprayer and a 07 CR 9080 NH combine and an old MF3080 for...

Fuses etc all ok but stuck in 4wd - which solenoid shall i check - there are several under the right hand step. Thanks for any help.

Looking for a set of 8 stud 600-60-28 floatation wheels for an air ride 3000 - thanks for any replies. Have 80% good set of Trelleborg 680 - 26.5 wheels as a trade etc - need a tractor pattern for our banks.

Asking on behalf of my cousin whos looking for a couple of second hand rotor drive cogs ( bed ) for a 3003 ph. He has rang Andy Guest with no joy ??!!

As above - gone very slow and mostly refuses to load - anyone else ? Is there another as good for a tower computer thanks .

We have a KV EG 85 300 auto reset variwidth fixed 6 furrow plough. Has anyone sawed through the beam and turned one into a 5 plus 1 - looks straight forward enough ? Thinking of welding a bracket each side of the vertical main beam before chopping to ensure it stays true , offering sawn section...

Stupid question probably but having upgraded to a 50hp fan on a central tunnel it is drawing air from mostly now inside the shed - imagine we should make a chimney out of shutter ply and draw fresh air in for best results ? There is no extractor fan in the building - thanks in advance.

Have a field in second continuous spring wheat and doing a great job on the blackgrass problem. Question is if we carry on would it get take all or is it a bit risky - tia .

Anyone know of a supplier for large spiral ducting for drawing air in for a grain fan ? Thanks for any replies.

Youngest (24) missed out last season due to covid the chance to work the winter in NZ or Australia after finishing at Reaseheath. Hopes to pack his bags this autumn after harvest here - experienced with large modern kit esp Fendts etc . We were told of a contractor in New Zealand by the name of...

We now have a 6m pronto ( one with curved disc carriers ) - are they good enough to plant spring beans ? Do i lift up the press wheels to get more depth and wind up the pressure on the screw jacks and drop forward speed ? Probably sumo and power harrow in front - thanks for any tips.

Sometimes when lifting high ( eg loading a lorry ) the boom seems to stick on the way down for 5 - 10 seconds and then goes down ok - would this be a solenoid problem ??? Thanks for any ideas.

Our T8050 - basically a blue Magnum is GPS ready ( i know little about it ! ) and has a rectangular plate on the cab roof with a clip each end and plug - what am i missing ? Big screen inside showing gps stuff in a past life - would it be Topcon or Trimble etc - thanks.

50hp Rekord crop drying fan - bit bigger than a pallet - will have dimensions soon. Somewhere close to Hereford would be fine - eg Gloucester , Worcester etc. Thanks alan 07971185224

Probably a David King job but the datatronic box ( under the cab offside ) does not switch off when turning the tractor off and so runs the battery down. Pull the fuse out on the yellow wire at the front and the lights go out and box shuts down - so we have rigged up an inline switch which is...

We are looking to buy an approx. 2000hr MF7726 vario. Is it a must to have one with extended warranty - have always serviced our own in the past - thanks for replies.