Search results

  1. 3

    Manitou MT732 Throttle faults

    Hi has anyone had a similar fault on a manitou with a Deutz engine. No throttle I suspected a throttle pedal fault but it seems to test ok on JALTEST. And apparently not uncommon for wiring issues..
  2. 3

    Manitou MT732 throttle faults

    Morning no they sent me a video but couldn’t see any codes on the display.
  3. 3

    Manitou MT732 throttle faults

    Hi got a manitou MT732 with a duetz engine and the throttle is sat at a raised ideal speed and won’t rev up. Has anyone had any issues with the throttle pedal potentiometers.
  4. 3

    John Deere 7700 wiring diagram wanted

    Morning yes that’s my mistake it is the ccu I wasn’t aware they were in two halfs.. we have sole other issues where the dash back ground light on the lcd flashes on and off and there is a low voltages across the fuse for lights. And that goes from 0.98 volts to 4.87 volts at a petty regular...
  5. 3

    John Deere 7700 wiring diagram wanted

    Hi thanks for the message only just had a look at it again today after several months.. got a low voltage on wire 133 Orange.. also same wire bunker on a relay wire. Do you know where that feed comes from.. I put a separate feed into the 133 wire on the hcu but still love voltage on the draft...
  6. 3

    John Deere 7700 wiring diagram wanted

    Morning not sure it’s the fuse marked HCU from memory. This is why I’m after a wiring diagram
  7. 3

    John Deere 7700 wiring diagram wanted

    Morning yes that’s correct
  8. 3

    John Deere 7700 wiring diagram wanted

    Hi yes that’s the boy..!!
  9. 3

    John Deere 7700 wiring diagram wanted

    Hi yes error code for low voltage on draft sensor.!!
  10. 3

    John Deere 7700 wiring diagram wanted

    Hi thanks for your response. I have unplugged everything that I’m aware is on the 5 volt circuit but still that same. The HVU has been changed in its life as it’s got 7600 written on it but this was many years ago thanks again
  11. 3

    John Deere 7700 wiring diagram wanted

    Hi thanks yes they are all ok. We have low voltage directly out of the HCU wire to the sensor
  12. 3

    John Deere 7700 wiring diagram wanted

    Morning the draft sensor.. that’s correct 5 volt feed out of the HCU. However we only have 1.7 volts. With the sensor connected and disconnected. Input voltage to HCU seem good.!! But would like to check the system through properly with a wiring diagram. Thanks
  13. 3

    John Deere 7700 wiring diagram wanted

    Morning. Keeps blowing the accessories relay fuse. And low voltage to the draft link sensor switch. She has had some previous repairs and modifications to some areas of the wiring over the years from what I can see.!!
  14. 3

    John Deere 7700 wiring diagram wanted

    Hi has anyone got a wiring Diagram for a John Deere 7700 Tractor. Happy to pay.!! Any help appreciated
  15. 3

    Cushman hauler Pro charger fault

    Hi can anyone help with a couple of faults on a Cushman hauler Pro 72 volt buggy. The charger isn’t working and showing a 6 flash code which I believe is an internal charger fault. Is there anything else to check before we order. Charger. Also the BDI isn’t reading battery voltage does the BDI...
  16. 3

    Kramer 418 hydro static drive sluggish

    Hi all.. has anyone got any knowledge of a Kramer 418. We have one with sluggish drive in forward. Carried out a stall pressure test and in reverse stall pressure is at 4300 psi and she pushes well and spins the wheels.. and in forward stall pressure is higher at 6000 psi but with no push and...
  17. 3

    JCB 527-58 AGRI plus. Error code P0641-00

    Hi what model is it.!
  18. 3

    Kramer 418 loader hydro static drove sluggish

    Hi all.. has anyone got any knowledge of a Kramer 418. We have one with sluggish drive in forward. Carried out a stall pressure test and in reverse stall pressure is at 4300 psi and she pushes well and spins the wheels.. and in forward stall pressure is higher at 6000 psi but with no push and...
  19. 3

    JCB 527-58 AGRI plus. Error code P0641-00

    Hi ok we had many codes but check the engine loom it’s mounted vertically down on the right hand side of the engine. Remove the belly plate underneath and you can see the plug it’s tight to get to but remover the two bolts from the brackets and check that plug. Put a small cot I the loom cover...
  20. 3

    JCB 527-58 AGRI plus. Error code P0641-00

    Hi have you code other codes or just that one m. Does it come on during cranking to start it
Top