I've got a pre isobus amazone sprayer with an Amatron+ screen. Can I link it to an agco C3000 screen in a massey and control the sprayer with the C3000? I've seen a video on YouTube with a topcon screen doing this.
If so, can you tell me what cable I need.
Thanks.
@Northern farmer
We have cowcare rope scrapers that scrape onto slats in front of the robots. I'm wanting to put slat mats down to help with white line as cows always seem to bull on the slats. Has anyone successfully got a scraper going from concrete passage up onto slat mats without it jamming or damaging the...
Recently bought a Massey 7618 with Autoguide 3000. If you travel over 8 kmh,
the steering constantly weaves about 50cm either side of the centre line.
Have had the software updated and no joy.
When calibrating the mounting bias, it doesn't steer right when it should.
Swapped the dome and the...
I'm getting intermittent error codes
5002 "Rear PTO Brake Solenoid stuck on"
and
5003 "Rear PTO Brake output open circuit"
Sometimes does it first time each day and if you disconnect the battery it's fine for the rest of the day.
Washed tractor yesterday and it's doing it constantly now, as...
Looking for a 7480-7495 or 76 equivalent.
Up to 6000hrs, preferably with Datatronic and 4SCV's.
Air brakes, front linkage/PTO would be a bonus.
Thanks.
The PTO engagement on our 65 reg 7618 is rather savage, not a problem on most implements, but went crimping with our KC Bruiser 1250 today, and struggled to engage the PTO in 540 without either breaking shear bolts or nearly stalling the engine, and sounding like it's trying to rip its guts out...
Has anyone fitted a tractor kit from them?
They are nearly half price of the rest at £1375, but it sounds a bit like a universal kit with no specific brackets for the compressor etc.
He was pushing the hydraulic powered Compressor which could be mounted anywhere, but there isn't much room on...
We always have problems with UJ's on our crimpers, don't get much more than 12 months and have problems, they run hot. We use the red lithium grease, is there a better alternative?
I want to tee into the spools is our T7-210 New Holland. Where can I buy the fittings to fit between the spool block and the existing m22 couplings? Parquìp could help last time I asked. Local stealer is about £180 to do 4. I think theirs came from one of the loader manufacturers. Cheaper would...
The compressor on our 7480 cab suspension is shot and the tractor doesn't have air brakes. I'm sure I remember reading somewhere about a company that sells a replacement at a fraction of the cost of a genuine one, but Google isn't finding anything. Anybody have any ideas where I can find one?
Father in law's got a new fert spreader, and he unhitched it with the shutters open. Went to use it again today and can't get it to work. Any suggestions?
2008 Renn Crimper/mill, 2 x 24" Roller mills on the same trailed chassis - pto drive, magnets, elevator discharge, 8' x 8' hopper - load from 3 sides.
12-25 Tph on Barley, 15-30 Tph on Wheat (depending on moisture and sample)
Good working order.
£10,000 +VAT
libary picture, will post some later.
Looking at getting a new trailer, only need for grain/muck. 12/13t 16' body with hyd tailgate and 550 tyres.
Long term trailer, got to last near the coast.
Has anyone got a fairly recent NC one? would like to know your views
Looks well built, with box section around the top of the body, which i...
I've bought 2 Ubiquiti Picostation M2HP access points. I mounted the first one on the chimney of the farm house and am really pleased with the range. Then i put the second one in the dairy building which has internet access from the same router via a fibre link, but I can't connect to this one...
Looking at putting up a turbine, 15Kw is the max grid connection we can have.
Initial desktop wind speed figure is 7.2 m/s @ 10 metres.
We will use most of the power ourselves for our milking robots.
Got the Kingspan rep coming out, i know theirs is a "new" model, anyone seen one at a show?
Any...
Many years ago remember talking to a New Holland sales man about a chain and slat round baler, he told me they were working on a conversion so you could put on plastic film instead of net. We will not have enough room for all our straw in sheds and we don't have a bale wrapper, just wondered if...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.