Search results

  1. L

    Claas 7030 wont release 3rd service pressure

    0013018720 little one 0013003200 big one
  2. L

    Claas 7030 wont release 3rd service pressure

    Could be electrical or the big accumilator has gone as well. If you hear a gas escaping should be OK if not much gas and oil come out accumilator has failed. The bigger one of the 2 by rear right wheel is boom suspension dose the orange light come on in the cab for it?
  3. L

    Claas 7030 wont release 3rd service pressure

    Chech if there is gas in little accumilator just undo alen key screw on top
  4. L

    Claas 7030 wont release 3rd service pressure

    By right hand rear wheel chech of the little accumilator has gas in. That supplies pressure to servos with engine off. Will boom lower when you push buttons to de pressure
  5. L

    split ISO ?

    You can split the screens
  6. L

    split ISO ?

    Yes you just need a splitter got this from as communications
  7. L

    Wire ties for use inside a engine

    Think with the vibration of the engine metal ones would cut through the looms after taking the ones out of engine have managed to find some £50 for 100 but better safe than sorry
  8. L

    How to set up your own RTK base station.. for about £300

    We have been using the old reichard 2g modems but there obsolete now John deere do there own modem just wondered what else is compatible we use v55 sierra ones on anything else
  9. L

    How to set up your own RTK base station.. for about £300

    For a jd star fire 6000 what type modems could you use rtk on ntrip account? Can any off the shelf one be used or dose it need to be a specific one?
  10. L

    Wire ties for use inside a engine

    Wire ties to hold injection loom to pipes inside the engine its a cursor 13 ftp engine
  11. L

    Wire ties for use inside a engine

    Was after some wire ties for using inside a engine would need to be oil and heat proof. Carnt find part no for the originals
  12. L

    Claas Scorpion 7044 boom inoperative

    The seat switch would be a good one to test as none of those functions will work if that fails.
  13. L

    Oil pressure class scorpion loader

    Should be a button on left hand side of the boom near the carriage you can push to de pressurise them
  14. L

    Claas celtis 456 radiator temperature problem

    Has it got the d10 pump with black module under injection pump?
  15. L

    Claas Scorpion 6030

    Have you checked fuel transfer pump that's driven by the water pump belt see how much wobble is in the pulley. Clean all the plugs to engine ecu they liked messing about with bad connections When they injectors wear out on those normaly will start when cold but not hot. Might be worth running...
  16. L

    Lexion 600+

    Can normally tell by the paint difference on them to original block. Have a quick Google of how much a om502 la is there not cheap and hard to get hold of now. If you bought it and had plenty of time you could take all the heads off get new valves put in and heads reconditioned it's not too...
  17. L

    Lexion 600+

    Worked at a claas dealer for 15 years trust me you won't do hydro for 10k. All 600 had the om502 la v8 merq in them claas had a lot of trouble with them dropping valves they changed all the cylinder heads on them at one point to sort it. They were in a few claas combines but 600 always seemed...
  18. L

    Lexion 600+

    Would avoid a 600 with high hours threshing wise wouldn't worry every thing can be repaired easily. They have a nasty habit of the hydrostat going bang normally fills the system up woth rubbish.The pump and motor are well north of 30k common problem on all 600. They also run the om502 la v8...
  19. L

    Claas Vario 560 reel forward and back not working

    What's the serial number of header is it a new type with no rape filler plates?
  20. L

    650 lexion unloader drive chain.

    Just put some marks on the sprocket before you take the chain off will be glad of them if chain snaps with a full tank won't have to take panels off to time it
Top