Search results

She is seized from sitting so not sure what else she needs. Paid less than you would for a 135

My brother picked this up a couple of weeks ago, was stripped down 8 yrs ago to fix a bit of rot on the mudguards. The cab was removed and set outside next to the dung heap, the rest of the tractor spent about 4 years or so in a cattle shed then was pushed outside and a silo cover pulled over...

Of all the Milwaukee gear I have, (a lot), the m18 torch I have is by a long margin the most disappointing piece of Milwaukee gear I have bought. If I had any HiltI m22 batteries I would have their torch in a heartbeat, it’s fantastic. As for standalone head torches I have a number of led...

The people were flying through when we got there and there was a right queue for the breakfast rolls @7:45, I did hear they didn’t open the gates to 8 the first day and there was good queues at that time. As for the Amarok, she is on her way back to the VW dealer in England where I bought it...

Went to this on the Wednesday myself, left the house at 4:45, onsite by 7:45, spent the day in the machinery section alone in busy busy crowds and was back on the road by 3 to miss the Dublin traffic, was going well until my new to me 3yr old Amarok decided to self destruct 50 miles from home.

Bought this a few years ago, its a big animal, that’s a 3ft bucket in it. Hodge Clemco with media recycling and separating and has done virtually nothing. Have a pallet full of glass abrasive with it too. I haven’t had it running properly yet, had it going but the road compressor I had wasn’t up...

Doesn’t look a great fit to be honest, I didn’t think I had to modify the holders, though it’s hard to remember everything, how secure does the clip hold it? You could try to run with them bulbs to see would they be bright enough without the expense of the led, the led bulbs would definitely be...

That is the same bulb as I replaced with the ones above. Try an ordinary halogen car light bulb in place of the one you have and see does it fit, if so then the led above will too. I don’t think I had any modifying to do to the headlights, one was an original unit and the other was aftermarket...

These fitted into the original headlights with no problem

Massey 298 I rewired recently, owner wanted led lights everywhere on it, so that’s what he got, headlights also have led bulbs in them, dip and main beam, I think they were about £30 or so from Amazon.

He has taken a big hit on price since it was for sale by Dave in June 2018 https://picclick.co.uk/2014-Swift-Challenger-Sport-554-Fixed-Double-Bed-292565223283.html

Thanks Gapples, when I first discovered the problem I did adjust the control rod but it made no difference, so I set the length back to where it was initially and checked it against the manual and it was pretty close to the proper measurement as far as I could judge with a tape measure. There...

So I tried this today, it did lift the arms a small amount more but nowhere enough to engage the hitch. I now believe it must be some from of internal adjustment needed as the drop rate slows right down long before the lift lever reaches the step at the bottom of the gate, it should only slow...

Thanks, I will try that, although I don’t know if it will raise it by the amount I need, I will maybe get a few pictures too

No, they stop about 4” below starting to lift the puh bars.

Hi guys, I have recently bought a wee 574 as a bit of a project and to have a handy wee machine about the house and to settle a nostalgic itch, memories of hauling grass with one years ago (rose tinted glasses) This was her when I went to view : Now I have it looking a bit better, power...

Have a front nextbase dashcam in my land cruiser since two minutes after I bought it and before I left the guys house in London to drive it home. Had a BlackVue front and rear system installed in the wife’s Audi when we bought it, I removed it when we changed the car nine months ago fully...