I have a v10 with about 100hrs on it. If I play with the ground pressure adjustment, the left mower pops up, the only way to keep it down is to run at max ground pressure (minimal float). What could be wrong here, is it one of the solenoids? Hard on skid shoes and I will wreck something if I hit...
I need a case drain line from an implement hydraulic motor, can someone confirm which line I would use as the case drain (return to tank). I have the three power beyond connections, I believe I should be connecting to the large top Return Oil Line, correct? (Labelled as (1) in the manual)
Not...
I can't find anywhere that states what differentiates a JCB Agri spec loader from a non-Agri spec, does anyone know? Specifically I am looking at a 427 Agri vs standard 427.
Looking at this used wheel loader, approx 5500 hours. It looks fairly clean. How reliable are these? I am looking for a high lift loader, this specs well in terms of lift height and weight but perhaps underpowered. Want for stacking 5x6 round bales, couple at a time, loading trucks, grapple...
Does anyone know offhand what ground pressure setting they are running their system at on the controller/isobus? Also, are you using the recommended linkage height settings as per the manual, or something else?
Manual says 1370mm to top link on the front and 825mm to lower link on the rear...
For farm use lifting and handling primarily hay bales (round), with spears, am I correct in assuming the tool carrier /parallel linkage is the preferred style over conventional z-bar? I wanted a high lIft boom but not all brands have parallel design with high lift.
What do you guys think about the new tire, it sure looks interesting for all around use. Whether it wears longer than traditional tire, I have no idea.
https://www.agdealer.com/articles/michelins-new-crossgrip-ag-tires
Can anyone tell me what the three settings mean on the manual ‘knob’ that is on the front of the Q Compact Valve (the loader valve block) on a Quicke loader?
Thank you.
Also, if the check valve has failed or is stuck open, can that be why I have no loader down pressure?
Probably a simple question, but how do you get your swaths where you have driven to show/highlight on your map? To highlight behind your guidance line I mean. Is it one of the layout tabs that you need to select on your custom Run screens you set up?
I see Tehnos makes a folding triple combination, are there any other brands available?
http://en.tehnos.si/universal-flail-mowers
No Tehnos dealer around.
Can these tools be set to cut at say 10-20cm or are they designed to be operated at 5cm or less?
I had a leak on my loader quick coupler. I tightened the fittings and ended up wrecking the JIC fittings, and so changed out two hydraulic lines on my loader circuit leading to the quick connect coupler. Anyway, both were for the raise/lower (same circuit). Obviously breaking apart these lines...
I am looking at adding new tractor, have T7.270 now, and was comparing the T7HD and lower end T8 (320 or 350).
You can get similar power.
They weigh basically the same.
The wheelbase is 50cm longer on the T8.
Once spec’d the same, the T7.315 is priced just slightly more than a T8.320 and less...
Any options on the 800 series with the triple mowers? I know most would say go for the 900s, but I need a front loader for bale moving and can’t get loader on the 900.
I run the Pottinger V10 setup (with 3.5m front mower), with roller conditioners, with a NH T7.270. Tractor handles the mowers...
I have a T7.270 that I am happy with, I find the ride rough as the wheelbase is already short. I need another tractor and am looking at a T7.210 that has everything optioned like I want, but am concerned the ride will be horrendous with the even shorter wheelbase. It does have the front axle...
I want to replace my T7.270, and was going to go with the T7.315, but it appears it may not accept a front loader (or is not available). I don’t really want to step up to a T8 for the sheer physical size. Other options would be the JD6250R or else Fendt 828, because the Fendt 900 series do not...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.