Search results

Got a small trolley jack from them few years ago thought it might be handy for small jobs, first use the plunger broke off linkage returned it for money back and got a better one from different place, yet i got a Chinese 4.5" grinder from Wickes for £8 many years ago been brilliant, seems...

That is processor which can be repaired, also used in early 40series pre-quad mod sle edc which could be dangerous when trying to attach implement and was only cured by different processor it was only after i spoke to Fords that we found out that it came from car side, all because the car never...

Possibly check valve seat, ball pitted or spring weak or broken to get at it is top cover off, remove ram cylinder and between top of cyl and cover there are two valves one is retained by circlip ignore that and remove the other one, it has a small groove around top, using a thin piece of wire...

So what model 4000 ?, will come back to you later i am not like you rich farmers as always something to do, lol.

The pump should not be constant pumping if you look at linkage there is a small pin that protrudes over edge of lift cylinder so when lift arms reach top the piston is pushing the pin and linkage which is attached to control valve into neutral, the lift lever quadrant may be marked with a small...

System cannot be bypassed and box in cab should have two knobs a lcd screen and lift lever has a potentiometer, David King electronics can repair them but if parts are missing i doubt it can, also the other components all need to be in working order, the lcd screen shows position of arms and if...

82.5mm is measured from the top of quadrant that lift lever sits in to front edge of lever in draft, the unload valve should be an easy sliding fit i have used valve grinding fine to achieve that.

Surprised to hear pick-up blocked but at least thats another tick off list, unload valve can stick and as it's so long ago now i am not sure but think steel ring was replaced by a sintered ring and later models with o-ring sounds like it has stuck again, as for draft and position they must be...

Note original cnh oil was multi F which was a thicker oil but even if cnh dealer has old stock it will be stupid price, as multi G is thinner it may induce a hew oil weeps and never forget 2-3-4ooo had separate oil levels on transmission and rear axle.

Unlikely to be clogged screen could be something as simple as woodruff key sheared on main pump gear likely if nut has loosened as this is twin [ main and pto ] pump, the unload valve in top cover can stick but that would not effect pto, up to you but i would remove pump then you can see drive...

Never use ether use brake cleaner it's less volatile, and there are no filters to glean on hyd's and if they worked before you took box off it's an induced fault, what cover are you going to remove to see gear,

First look at two multi-pin connectors under right front of cab spray electric cleaner on pins Codes E38-45 go through them also look under cab floor panel wiring can get damaged.

Never ever had a problem on 570-5, first check feeder rotor timing in relation to each other and also to plunger, there is also an adjustment at top of feeder fork 3 holes if it's in top or bottom hole put it into middle and check after baling a few.

I did one about 3yrs ago but not really the right way, remove bonnet and infill panel and support, 4 small bolts attach this to cyl head battery and tray, rocker cover and rocker shaft which has some cyl head bolts through it, these you take a chance on as one should not remove some head bolts...

More than likely it's the internal linkage inside which means top cover off but if you have never done one some don'ts, do not lift top arms right up by hand or rod inside may drop out of lift piston only piston end but if you have just refitted top cover it's off again, do not adjust any...

Didn't see many old faces possibly because there are less of us.

My old firm so i will go.

This should help.

%000 were bored block, Major had cast liners and seals, , liners for subsequence blocks after this will be spun steel and pressed in.