Search results

Friends one leaking oil from spool valves did replace two about 3yrs ago and either the two others are leaking or same ones, went to local j/d dealer today and tried to get an o-ring kit he did have one but when i dismantled an old coupler they are bigger than in kit is it possible to re-seal...

Has anyone got a repair manual for this that they don't want anymore, parts one would also be helpful and before someone yells out get them from web yes possible but today people seem to want paying for information, i don't mind paying for a genuine book but they are all photo copies and some...

Anyone able to post photo of pto lever on 2120 am sure it's one of two levers below range lever 12x4 gears, outer one nearest inner mudguard was seized but after freeing it off pto not turning, lever next to it i suspect being for 4 w/d and don't say try it if you see the state of machine it's a...

Any one know if the vertical type of fuel tank tap should have a small filter on top, seen new taps for sale but no filter.

Done just over 8000 hrs but turned over a lot before starting changed filters and fitted seal kit as one seal was missing better than it was, but taking about 9sec to start have also fitted new hose tank to filter. i know i can fit non-return valve but is 9sec to start ok for these hours.

Merlo 26.6, 2000 aeriation of hyd oil can be heard and felt on joystick am going to change return filter but how to remove suction one, which manual states needs no servicing.

Anybody tell me if i put a 30w led floodlight in a barn about 25ft nigh in apex to shine down enough to see to fill buckets with feed from back of tipped trailer would that be ok, as next one up is 50w, which i know would be good but trying to cut back on electric, it's stated 30w ok to light a...

Old honda fourtrax permanent 4 W/D quad bike, front and rear axles 4 wheels and tyres, carrier, driveshaft, no engine, bodywork or frame, £150 buyer to collect, cash only. 07891862405, Essex.

I have a 6" monitor and box which i was given 6-8 yrs ago but don't know what it's off can't post photo, screen marked bv-750, row of small buttons down right side, box marked bv-700cw, power socket 4 pin marked 12-32v, sockets cam-1 and cam-2, other side cam1 & 2 to monitor also jack plugs...

What make and type of tester are people using, i have a snap-on one has for years but switch and toaster element insulating board broke, then had a cheap sealey one given to me but no good so thinking electronic one better, needed for all types of battery, but don't want to pay stupid money.

Can anyone tell me what type of plastic pto guards, more so the tubes are made from, my own guess is polypropylene, but not sure.

Any one know where rear axle steering valve and solenoids are.

Might be one for ace, when ign switch turned on nothing moves on dials or dash warning lights, move key to start alternator, eng oil and brake lights come on and top right dial needle goes fully over, after eng running nothing on dash, idea's, ?. did check all fuses two blown and replaced but...

Have been looking at one for friend ok at start this year but suddenly started to vibrate and chatter like disc knives touching, found one disc very loose as square hole worn so this was replaced along with new hub, old grease removed and new stuff put in vibration gone but still noisy only bad...

Anyone know twin blade topper rubber doughnut gone, in parts manual no part number shown only diagram number, surely one do's not need to buy complete shaft..

never used this before, normal operator not here anymore, owner tried it today operates ok but after wrapping finished he has to press auto start again to tip it off table which is what it states in manual but owner thinks it should do it all automatic is he right and how do we get it to do so...

May have asked this before,anyone know where to find engine number and tractor serial number on a 4cyl, 5,6, or 7 series no idea of year it's got ta transmission.

Anyone seen latest idea from a Boris M.P. ,apparently old farmers should retire and let young ones take over, some of these mp's must live on another planet with some of the cr-p that comes out of them............

Hour's on rpm clock most of time blank but when it do's appear the hour's are still going up when used,is it the clock ? or something else.......

bucket locking pin problem at moment they will come out but not in, engine under load when coming in but nothing trying to go out, switch has been swooped with boom one, no good, have tried moving wires about but no good when i tried it just a few days ago worked perfect, have been told its the...