trimble

GM035804 - Trimble Modem Advert added by: Chandlers (Farm Equipment) Ltd Machinery Details Category: GPS and Farm Electronics GPS and Precision Farming equipment Price: £1650 Condition: Good Description Used Trimble Modem How to make contact with the Dealer Click here...

Is anyone using the new all in one PBC's? Just about got my original PCBv2 system fully operational, and my mind moves to the next tractor - but there have been so many jumps in the technology since then!

VA00133B - New Trimble AG-482 GPS SM Receiver Advert added by: Chandlers (Farm Equipment) Ltd Machinery Details Category: GPS and Farm Electronics GPS and Precision Farming equipment Price: £2500 Condition: New Description Trimble AG-482 GPS SM Receiver C/W Top Doc...

In the next 6 months we are due to take delivery of a guidance ready MF. A NovaTel basic receiver is pencilled in, but very cancellable. We have 2 topcon units, one is an aged Agco unit, hence the reluctance to take the Agco NovaTel. But Topcon give the impression of moving away from guidance...

What will a rough cost be? Looking at fert spreaders and they tend to be isobus 2015 onwards. May aswell try for autosteer aswell. We run a Massey 6480 t3 with datatronic (old isobus) I don't think this will do much with a modern machine. Can I add the data5 screen etc with a view everything can...

Big bud tractors are re entering production soon They will be computer free zones!!

I've had the above error popping up on my Tier 4b T7, usually it does it a few times a day and the only way to clear is switch the tractor off and on again, it's very annoying when drilling and everything is setup. The error on the screen suggests to update the firmware, I've had the main...

Does the ready built in gps on case tractors work ok and simple?

Thinking about getting the unlock code to enable section control on my Trimble gps. It’ll link to my Kuhn Axis fert spreader. Is it worth it? Will cost around £1100

Trimble cfx 750 Advert added by: @ih1455xl Machinery Details Category: GPS and Farm Electronics GPS and Precision Farming equipment Price: £1000 Condition: Used Description Used Trimble CFX 750 includes AG 25 receiver , full wiring harness for Sam 200 steering motor...

Wrote up a guide on how I did this, feel free to check it out: https://discourse.agopengps.com/t/steering-a-22-mf-6718s-over-canbus/11955 (or if you don't care and just want to see the results.. :p)

A longshot, but looking for a new secondhand antenna for our old EZ500 GPS, an AG15 according to the book. The old one fell off the roof of the Bateman cab and sat nicely on the exhaust where it burned a hole and filled with water before we realised. One from a 250 or 750 would probably do the...

Looking to invest in a new fert spreader. Had a twin disc sulky spreader covering ~150 acres. What are my options in terms of more accurate, high tech features? From what I've gathered it comes down to whether it has weighcells, section control and auto shut off. Anyone have experiences with...

Is it possible to put a T into an an in cab isobus plug, to produce 2 sockets from one. Or does isobus not work like that?

Just got a new Amazone ZA-TS spreader and we are having problems getting it to work with the section control on our XCN 2050 . Have tried both FM 1000 app and Precision IQ but neither work. Previously had another ZA-TS which worked fine, but now dealer is saying Amazone have new software which...

Bit of a long shot. I need a new/secondhand rtk radio to go in my fm750 Trimble screen. Anything about? Second one that's crapped itself.

Anybody use a reputable supplier? Looking to window mount a mchale bedder control box. TIA

I run topcon x35 and it’s suddenly really unreliable because it keeps dropping out and going into float RTK. When it goes into float it’s actually worse than the old EGNOS signal and it stays in float for hours then suddenly RTK comes back on for a short time before dropping out again. Any...

Just been thinking about it today.....would it be helpful to have a software/firmware thread on TFF in order to be able to share firmware updates?

After recording a boundary with the CNH system, I can create a field AB line parallel to any section of the boundary line on the screen, without driving along that section again. I can create a new AB line while in autosteer - for example along a straight section of a curved line. I can get...