xeobib

Is anybody running two weights per wheel on 7700 series - on 650/65 x 42 tyre. A rep. told me he wouldn’t advise on that - or 620/70 x 42 ? We are currently running one/ wheel

Some advice please . I have a Househam AR 3000 that came on Trelleborg flotations which looked great , big wide cleats with a diamond pattern in the centre and so lots of rubber on the ground but basically it is a trailer tyre and not a driven tyre . The only problem is that our ground is all...

Has anyone got a set of part worn 710/60 r38 xeobibs?

Hi All looking for some advice on putting 710 tyres in furrow. Gregoire Besson plough hrpw7 I think! should I be looking at furrow wideners or collapsing the furrow wall etc? Heavy land so will take a lot to fill the furrow after it’s been squashed with the wide tyre! would normally plough on...

Very soft ground conditions here at the min and alot of full slurry stores. I am looking for a big set of flotation tyres etc to fit a jd 150r then we can go and help a few people out. Can you get terra tyres to fit a john deere 150r? or are they a thing of the past? will they be fit for 50k...

We are running our RB35 (with 36m VG boom) on 710/55/30 floatations but find it treads a bit heavy, has anyone fitted any bigger tyres successfully? We weighed it empty today, the bridge said it was 9.5t

Hello all. I am trying to work out my options for tyre pairings on my T7210 AC. With the JD tractors the book gives you a calculation to work out what wheel pairings you can have and what the tolerance with rolling circumference variation is, because obviously not all tyres have the same RC but...

Your thoughts please, would Vulcanising the sidewall on one of these ever be a job with the amount of flexing involved?

Has anyone any experience of these or have any knowledge on them? They seem a cheap option, which isn’t always a good thing! We’re looking at getting some new boots for our T7040 and wondered if anyone had tried these as an option? Many thanks in advance.

The replacement for our 750a arrived today. Will run alongside the ULD converted CO6 tine option that is currently undergoing some changes. Very impressed so far, very operator friendly and well thought out design. Lots of new options for cover and companion cropping with x 4 hoppers and a...

This is just for a bit of fun and not for raising controversy please!! Been thinking about this for a while now after spending hours driving and repairing various makes of tractors..... If given the choice to build your ideal tractor from choosing components from various manufacturers, what...

Any suggestions as to what setup to go for if looking at 4000 litres between front and back tank, 30m booms, boom height control, so both front and rear tanks fill and empty simultaneously. Would be used for liquid fertiliser as well as water. What size tractor but not much road work involved.

I'm running a 6155r JD autopower on 650/75 r38 Michelin mach X big how low a pressure would you go to pulling a vaderstad carrier with ripper tines and paddles at 10k ? The tyre expert says 12 psi but there's no flex in the sidewall at 10 psi Also a 7930 on 710/70 42 pulling 4m vaderstad...

Probably no definitive answer but can any users help me find ideal pressures for my New Holland T7.210 on 650/65 38 and 540/65 . Best set up for comfort, grassland work. Thanks

what’s my puma 150 worth . 17 plate 1250 hrs. 40k no air brakes . 18x6 semi powershift . 600 rear trellebourg tyres. 1000kg weight pack on front bolster. Very good to mint condition

Sitting in the back of my shed I have a massey 6480 with only 247 hours. I never use her and to be honest don't ever intend to. Question is do I leave here and keep it as a future classic or sell it. It's on Michelin xeobib 650 rear 520 front. 40k. Auto drive. Closed centre hydraulics year 2008...

whats a good alround furrow width plough is currently at 20” far to wide just looking for abit of advice my ploughing all self taught an its quite a long job to close it up abit an really dont wanna have to do it to many times lol (its not vari width) kuhn 7f multi leader

We are looking for a new self propelled sprayer. Currently run a Housham ar. On 32m booms. We are looking to go lighter and potentially down to 28metres at the smallest but would ideally be a 30m machine. I've looked at the Housham spirit. But what other machines should I be considering. I don't...

Any idea what model this is? It's advertised simply as a '6m Simba cultivator', just doing a little research on whether it would be any good on heavier over wintered ploughing. I've never seen a Simba that looks remotely like it, which makes me wonder if there might be a good reason they...

i have a 2014 deutz ttv, and get a cab shaking/vibration only between 11-12kph since new, never really bothered me before but im planning on starting to spray around 12kph so started thinking about it again. is this because of the continuous transmission? thanks