Idiots guide to Milwaukee.....
- Thread starter simmy_bull
- Start date
davedb
Member
- Location
- Staffordshire
Same hear I’ve got a drill with a dodgy trigger and a impact gun with worn battery terminals
- Location
- Dorset/Wiltshire
Hi, I have one of these and I’m really disappointed with itOne of these is next on my list.... Never tried one though.
Milwaukee M18BRAIW-0 M18 Compact Right Angle Impact Wrench
Milwaukee M18BRAIW. 18 volt compact cordless right angle impact wrench. 3/8 inch square drive. 307mm length, ideal for working within confined spaces. UK equivalent for US Milwaukee Tool 2668-20. Milwaukee 4933447899.www.milwaukeepowertools.co.uk
- Location
- North West
In what way? I nearly ordered one but decided to go for the M12FIR38-0 as it look far more compact.Hi, I have one of these and I’m really disappointed with it
- Location
- Dorset/Wiltshire
It’s just got no go in it, I may of been expecting too much but it struggles with a small pipe clamp.
- Location
- North West
Just looked up the spec on my old bluepoint air ratchet which comes out at 60nm, I’ve always thought it more than adequate for wizzing stuff in and out. It’s enough to trap you knuckles if you don’t release the trigger fast enough anyway?
The Milwaukee is suppose to be a peek torque of 75nm so I’d say your probably expecting a little to much.
At the end of the day they are at ratchet not an impact driver.
It won’t pump grease into the nipple but it continues pumping grease so ends up a mess.
ACEngineering
Member
- Location
- Oxon
So you just need a new coupling on it. No big deal. Due to lack of pressure relief valve they eat coupling for breakfast, lunch and dinner.
Last edited:
Is the genuine coupler better than a generic 4 claw one. I have been using a sparex clip on one but that is leaking now
ACEngineering
Member
- Location
- Oxon
dont have milwaukee gun, i got alemite and only use Alemite 3 jaw slim couplings which come standard on it. Buy them 6 or so at a time of Allube, about £3 ish each i think from memory. Tried sparex and vap coupling in the past etc and there all crap compared to an Alemite one and more expensive i think?
Just buy this one, anything else I've tried over the years was a balls.
Lock on quick release G coupler grease gun coupler-Long version-Doost D600 | eBay
Lock on quick release G coupler grease gun coupler-Long version-Doost D600 | Vehicle Parts & Accessories, Garage Equipment & Tools, Workshop Equipment & Supplies | eBay!
rover.ebay.com
Gerbert
Member
- Location
- Dutch biblebelt
Has anyone tried a milwaukee hedgecutter, or the long stick thingy which can take a mower, chainsaw and hedgecutter attachment?
They look the bizz but stihl and husqvarna don't seem more expensive, which seems a better choice.
They look the bizz but stihl and husqvarna don't seem more expensive, which seems a better choice.
Niall310
Member
cheers for that! I think I'll go for the cheep option grinder then, It would be hard to justify £285 when i could buy a dril and grinder for less than that.
Niall310
Member
Where do you buy the Alemite ends? I struggle to get any decent ends.
ACEngineering
Member
- Location
- Oxon
- Location
- North West
Santa’s come early ?
Pistonbroke
Member
Ho ho ho..ly crap!
dee
Member
- Location
- Derry/Londonderry
Time for a safe now to store all them goodies in
seedman stains
Member
- Location
- lost in france
Santa Emptied his sack a bit there!!!!!
Last edited:
Where’s the best deal for all that lot?