Kuhn FBP 3135 v Mc Hale Fusion

Grassnslurry

Member
Location
Ireland
Standard
Yeah they weren't selecting the way they should and one set kept dropping out at irregular intervals. Work properly now though.
Is your a 2018 fusion? Mine is and selectable knives arent working properly, only one set will stay up, have blanks in the other set
 

James

Member
Location
Comber, Down
Had the fusion before fbp kuhn and I moved purely because of problems I had with the mchale and in my area mchale backup not as good as the kuhn dealer , in fact there is no comparison between the two in terms of backup!
But running the kuhn last year on plastic ( not film ) like the mchale has I could see the difference in bale quality, baler also has far superior intake system especially notable in short grass , still packs it in very tightly
As jenks6910 said the protection on the bales in the field is noticeable side by side with fusion and bales holding there shape , would tell me there is more grass in the bales that hold there shape
Ps they were my bales jenks6910 was moving
How's your kuhn doing for you? Have you had any issues or problems? Many bales through it? PM if you prefer
 
How's your kuhn doing for you? Have you had any issues or problems? Many bales through it? PM if you prefer
Hi
Very pleased with the kuhn , it’s done 12k bales now , had one problem last year when a short shaft sheared going to gearbox , was up and running next day , looked to be a floor with the shaft and think a few have had same issue and been upgraded same as mine
Copes with the early short grass a lot better then previous McHale balers , and also hardly ever get slip clutch going off, it has hell of an appetite!
Plastic going on the front no problems at all and the 3D wrapper on back does brilliant job , no waste on any of my bales and customers all converted to all plastic on silage / Haylage
 
I have a kuhn bio, not a FBP grant it and I have a fusion 3 plus and the kuhn stays in the shed while the fusion does the work. For me the Fusion is in a different league in terms of toughness, reliability, parts availability and resale.
Your not comparing like for like really
 
Hi
Very pleased with the kuhn , it’s done 12k bales now , had one problem last year when a short shaft sheared going to gearbox , was up and running next day , looked to be a floor with the shaft and think a few have had same issue and been upgraded same as mine
Copes with the early short grass a lot better then previous McHale balers , and also hardly ever get slip clutch going off, it has hell of an appetite!
Plastic going on the front no problems at all and the 3D wrapper on back does brilliant job , no waste on any of my bales and customers all converted to all plastic on silage / Haylage
EF185CBA-4503-43B4-B851-F82867CA5E7D.jpeg
9D0F6B51-08AD-4AEA-970E-1D280AFE7C9C.jpeg
8B22F649-D300-46F9-B12F-349727067D17.jpeg
 
They look great. I can't see my fusion making as neat as those. The short time I had one to try I found some of the density settings a bit confusing.
I had McHale on max density and couldn’t get bales tight enough on short grass , they would sag
These Kuhn bales hold there shape
Density settings easy enough on touchscreen
Just need day or two to get use to it
 
Last edited:

AGCO reports sales increase of 43.5% compared to 2020 figures

  • 101
  • 0
Written by Agriland Team from Agriland

The tractor manufacturer AGCO, which consists of brands such as Challenger, Fendt, GSI, Massey Ferguson and Valtra, reported its results for the second quarter ending June 30, 2021.

Net sales for the second quarter were approximately $2.9 billion, an increase of approximately 43.5% compared to the second quarter of 2020.

AEM

Reported net income was $3.73/share for the second quarter of 2021, and adjusted...
Top