Kverneland t8 wrapper

[Johnny Deere]

Hi there I am trying to get this wrapper steering axle set up.
I've it on the tractor drawbar not the baler but the steering axle doesn't seem to work.
I have it calabrated and it works manually.
I'm getting error code 18 and 16 pop up.
Thanks

 

[valtra]

have you got an operators manual? the error codes should be in there..i have the newer model to the t8 I will check my manual

 

[Johnny Deere]

have you got an operators manual? the error codes should be in there..i have the newer model to the t8 I will check my manual

Yes them codes aren't showing up unfortunately it's a workshop manual I really need

 

[Shane s]

i have the operators manual and the dealers service manual, the dealer manual gives you codes to go in and prgrame the wrapper and recalibrate everything, i had to get them from kneverland them selves, i can send this through to you if you like

 

[Brendan B]

Shane, I'n in the same position as Johhny Deere. Would you have the dealer PIN to access the dealer functions on the console?

 

[Johnny Deere]

Shane, I'n in the same position as Johhny Deere. Would you have the dealer PIN to access the dealer functions on the console?

42

 

[Shane s]

Shane, I'n in the same position as Johhny Deere. Would you have the dealer PIN to access the dealer functions on the console?

Yeah as Johnny Deere said pin is 42, if you want the full dealer and also the full operators manual send me your email via pm and I can send it across to you

 

[Shane s]

I'm having a problem with the timing on the cut and tie arms on my wrapper Still if anyone can help me, it is hitting the cut and tie arms of the dispensers because of the timing is off, I moved the sensor 2 years ago to suit the dispensers to stop further around so that wrap cuts right but I think I need to move the sensor back now and adjust calibration so that dispenser stops later through timing. With this done the sensor would enable the dispenser to go up and down to let go of the wrap earlier so that the dispensers won't hit them, any of yous any experience with this?

 

[Johnny Deere]

I'm having a problem with the timing on the cut and tie arms on my wrapper Still if anyone can help me, it is hitting the cut and tie arms of the dispensers because of the timing is off, I moved the sensor 2 years ago to suit the dispensers to stop further around so that wrap cuts right but I think I need to move the sensor back now and adjust calibration so that dispenser stops later through timing. With this done the sensor would enable the dispenser to go up and down to let go of the wrap earlier so that the dispensers won't hit them, any of yous any experience with this?

Give me a ring tomorrow and ill explain

 

[Pheasant Surprise]

42

Brilliant! The designers/programmers had a great sense of humour

 

[Brendan B]

42

Thank you Shane.

 

[Brendan B]

T

Yeah as Johnny Deere said pin is 42, if you want the full dealer and also the full operators manual send me your email via pm and I can send it across to you

Hank you JohhnJ .

 

[Shane s]

Give me a ring tomorrow and ill explain

ill give you a call tomorrow or thursday phones away getting fixed, will be wrapping with her thursday evening so will be fit to set up better in the field with the tension on the wrap

 

[Paul T6]

Yeah as Johnny Deere said pin is 42, if you want the full dealer and also the full operators manual send me your email via pm and I can send it across to you

Hello Shane
Would you be able to send me the operators and dealer manuals for a T8
Thanks
Paul T

 

[Shane s]

Well, Paul PM me you email address and i can send it on.

 

[Paul T6]

Well, Paul PM me you email address and i can send it on.

[email protected]
Thanks

 

[wdah/him]

As a general note what are the T8 wrappers like do they give many problems, currently have a 991be and need something quicker few of these on donedeal, not got good views on hs 200 as most have done big numbers.