Jonathandwelsh
New Member
Please feel free to comment on here if interested!
Full time work only please as I have a harvest job if I need it and I’m not looking for anywhere else just for the season.
Thank you kindly for viewing and all the best!
Qualifications:
• Category H track layer/crawler tractor.
• PA1 and PA2 spray Certificates.
• PA4S (slug pellets) certificate.
• PA4G (granular pesticides) certificate.
• PA6 (knapsack)
• GNVQ ICT - Pass (equivalent to 4 C grades)
• Full (Clean) Drivers License since august 2007
• Certificate in Basic Tractor Driving and Maintenance
• Teleporter safety and operation 1:1
• Fork Lift safety and operation 1:1
• CSCS health and safety certificate
• CPCS A59a 360 degree excavator card obtained from East Yorkshire (plant) training for both above and below ten ton machines (expired).
Agricultural Experience
Tractor driving up to 420HP (All major brands, wheeled, half tracked and rubber tracked)
GPS Technology (Trimble, Greenstar/Autotrack, Massey auto steer, TopCon)
Extensive telehandler and fork lift truck work.
Plant machinery work (360 excavators from 1 to 18 tonnes, Rollers, Loading shovels)
Ploughing (Mould board and Chisel ploughing/Dragging)
Power harrowing (4,5 and 6 meter)
Drilling (6 meter horsch pronto air drill)
Subsoiling (2-5 leg)
One-pass Cultivation (Vaderstad Top down)
Spring-tine Cultivating
Culti-pressing
Rolling
Baling (MF 2250 3x3 with sledge, MF2190 4x4)
Trailer work with grain trailer, low loader, bale trailer and header trailers and artic trailers with dolly.
Combining
Fertiliser Spreading
Vacuum tanking
Flail mower work (Hedges and verges)
Turning hay and straw
Muck spreading (Rear and side discharge)
Stock work (Chickens, Pigs, Cattle and Sheep)
Workshop work including welding and fabrication although this area could use some improvement!
Extensive manual work including drainage work, brushing and shovelling etc
Machinery maintenance, always like to have my own tools and my own grease gun with me, im a big fan of looking after machinery properly.
Full time work only please as I have a harvest job if I need it and I’m not looking for anywhere else just for the season.
Thank you kindly for viewing and all the best!
Qualifications:
• Category H track layer/crawler tractor.
• PA1 and PA2 spray Certificates.
• PA4S (slug pellets) certificate.
• PA4G (granular pesticides) certificate.
• PA6 (knapsack)
• GNVQ ICT - Pass (equivalent to 4 C grades)
• Full (Clean) Drivers License since august 2007
• Certificate in Basic Tractor Driving and Maintenance
• Teleporter safety and operation 1:1
• Fork Lift safety and operation 1:1
• CSCS health and safety certificate
• CPCS A59a 360 degree excavator card obtained from East Yorkshire (plant) training for both above and below ten ton machines (expired).
Agricultural Experience
Tractor driving up to 420HP (All major brands, wheeled, half tracked and rubber tracked)
GPS Technology (Trimble, Greenstar/Autotrack, Massey auto steer, TopCon)
Extensive telehandler and fork lift truck work.
Plant machinery work (360 excavators from 1 to 18 tonnes, Rollers, Loading shovels)
Ploughing (Mould board and Chisel ploughing/Dragging)
Power harrowing (4,5 and 6 meter)
Drilling (6 meter horsch pronto air drill)
Subsoiling (2-5 leg)
One-pass Cultivation (Vaderstad Top down)
Spring-tine Cultivating
Culti-pressing
Rolling
Baling (MF 2250 3x3 with sledge, MF2190 4x4)
Trailer work with grain trailer, low loader, bale trailer and header trailers and artic trailers with dolly.
Combining
Fertiliser Spreading
Vacuum tanking
Flail mower work (Hedges and verges)
Turning hay and straw
Muck spreading (Rear and side discharge)
Stock work (Chickens, Pigs, Cattle and Sheep)
Workshop work including welding and fabrication although this area could use some improvement!
Extensive manual work including drainage work, brushing and shovelling etc
Machinery maintenance, always like to have my own tools and my own grease gun with me, im a big fan of looking after machinery properly.
