Makita DCS 500

casemx 270

Member
Location
East midlands
I got a Makita DCS 500 which is a 50 cc engine, when I bought it came with a 18 " bar in my opinion it would run better on a smaller bar something like a 15 or 16 bar it's currently on a 5/8 chain but was wondering if it was worth going to a 0.325 chain bar and sprocket would I notice any difference to justify the extra money or just stick with 5/8 and get a smaller bar for it ??? Thanks
 

Lincs Lass

Member
Location
north lincs
You meen a 3\8th,, to change it to 325 you have to change the drive sprocket and bar.
50cc will run up 18inch bar, preferably 325,050 72 drive links, 3/8 is more for bigger saws unless you go for a 14inch 3/8,,058,,52dl
 
Last edited:

john432

Member
Location
Carmarthenshire
Find these very good for the money, Screenshot_20190309-195328_Samsung Internet.jpg
 

john432

Member
Location
Carmarthenshire
Search .325 rim sprocket in Ebay, 7 tooth should be fast enough. But I'm not a 100% certain that that they all have the same inside diameter and splines. But some of the sellers give the sprocket dimensions. Dont know why sites like northen arb, who sell chains and bars dont list clutch drums and sprokets, which are consumables.
 

casemx 270

Member
Location
East midlands
Search .325 rim sprocket in Ebay, 7 tooth should be fast enough. But I'm not a 100% certain that that they all have the same inside diameter and splines. But some of the sellers give the sprocket dimensions. Dont know why sites like northen arb, who sell chains and bars dont list clutch drums and sprokets, which are consumables.
Thanks for your advice I ll have a look l was just looking for makita one didn't think of a after market one
 

casemx 270

Member
Location
East midlands
Also the kerf of the bar is diferent ,,thats the slot around the bar ,,1.3mm is 050 ,1.5mm is 058 and 1.6 is 063
Thanks for your reply the kerf size what decides that slot size ? I have found a 7 tooth .325 rim sprocket but I m not sure what kerf my new bar and chain should be to be right, I know it's got to be .325 but not sure of the rest if that makes sense thanks
 

Lincs Lass

Member
Location
north lincs
Thanks for your reply the kerf size what decides that slot size ? I have found a 7 tooth .325 rim sprocket but I m not sure what kerf my new bar and chain should be to be right, I know it's got to be .325 but not sure of the rest if that makes sense thanks
The rim will take both 1.3 and 1.5 ,,I run 1.5 (058 ) on everything,,so if you are going to use a 15inch bar its 325/ 058 /64 dl ,,18 inch is 72dl
 

SFI - What % were you taking out of production?

  • 0 %

    Votes: 77 43.5%
  • Up to 25%

    Votes: 62 35.0%
  • 25-50%

    Votes: 28 15.8%
  • 50-75%

    Votes: 3 1.7%
  • 75-100%

    Votes: 3 1.7%
  • 100% I’ve had enough of farming!

    Votes: 4 2.3%

Red Tractor drops launch of green farming scheme amid anger from farmers

  • 1,284
  • 1
As reported in Independent


quote: “Red Tractor has confirmed it is dropping plans to launch its green farming assurance standard in April“

read the TFF thread here: https://thefarmingforum.co.uk/index.php?threads/gfc-was-to-go-ahead-now-not-going-ahead.405234/
Top