Pressure washer extension

jack_c

Member
Just reading the tractor cleaning thread and it got me thinking.

I currently have the hot wash in its own dedicated shed but would like to set up a wash bay somewhere else. Not seriously far away but maybe 150ft away.

Can I pipe the pressure washer to this area without loosing pressure? I currently have lots of extensions as it is but was wanting to do a fixed set up to new point of use.

Do I increase the pipe size then step it down at point of use? Better to use rigid pipe or stick with hydraulic hose that I'm using currently?

The washer is an Erle 923 if that makes any difference?
 

mo!

Member
Mixed Farmer
Location
York
Just reading the tractor cleaning thread and it got me thinking.

I currently have the hot wash in its own dedicated shed but would like to set up a wash bay somewhere else. Not seriously far away but maybe 150ft away.

Can I pipe the pressure washer to this area without loosing pressure? I currently have lots of extensions as it is but was wanting to do a fixed set up to new point of use.

Do I increase the pipe size then step it down at point of use? Better to use rigid pipe or stick with hydraulic hose that I'm using currently?

The washer is an Erle 923 if that makes any difference?
Rigid large bore would be best, you'll lose lots of heat over that length unless you insulate it well. By the time you've done it properly you'll be halfway to a second washer.
 

jack_c

Member
Rigid large bore would be best, you'll lose lots of heat over that length unless you insulate it well. By the time you've done it properly you'll be halfway to a second washer.
Would be mostly used on cold really but had thought that too.

Would lag the pipe anyway.
 

Wisconsonian

Member
Trade
Don't take my word for it, look up the pressure drop charts. The pressure drop required to flow a certain volume of water through a certain length and size of pipe does not vary with the pressure of the water, as far as I know. If you're buying a new length of hydraulic hose for this purpose, then I'd guess 1/2" would be plenty to keep the pressure drop to a minimum and not cost much more than 3/8", but do the numbers and see.
 

blackisleboy

Member
Livestock Farmer
Don't take my word for it, look up the pressure drop charts. The pressure drop required to flow a certain volume of water through a certain length and size of pipe does not vary with the pressure of the water, as far as I know. If you're buying a new length of hydraulic hose for this purpose, then I'd guess 1/2" would be plenty to keep the pressure drop to a minimum and not cost much more than 3/8", but do the numbers and see.
Correct....the pressure drop in the pipe will be tiny compared to the pressure at the pump. Pressure drop is a function of velocity in the pipe....if you use a larger diameter pipe the friction losses are smaller and the pressure drop is smaller. Its not easy to calculate accurately unless you know the technical details of the pipe - but as a rule of thumb keep the water velocity to below 2 metres/second and you wont have anything to worry about.
 

jack_c

Member
Flow rate of a pressure washer is not that high , so drag losses would be low

Don't take my word for it, look up the pressure drop charts. The pressure drop required to flow a certain volume of water through a certain length and size of pipe does not vary with the pressure of the water, as far as I know. If you're buying a new length of hydraulic hose for this purpose, then I'd guess 1/2" would be plenty to keep the pressure drop to a minimum and not cost much more than 3/8", but do the numbers and see.

Correct....the pressure drop in the pipe will be tiny compared to the pressure at the pump. Pressure drop is a function of velocity in the pipe....if you use a larger diameter pipe the friction losses are smaller and the pressure drop is smaller. Its not easy to calculate accurately unless you know the technical details of the pipe - but as a rule of thumb keep the water velocity to below 2 metres/second and you wont have anything to worry about.
Thanks for the replies,

Was thinking 1/2 should be enough, would you just go rubber hydraulic pipe? If going steel it would need to be stainless to stop it rusting.

Have already got more than this distance in 3/8 but was thinking if making it a permanent affair the 1/2 would be better.
 

SFI - What % were you taking out of production?

  • 0 %

    Votes: 79 42.9%
  • Up to 25%

    Votes: 63 34.2%
  • 25-50%

    Votes: 30 16.3%
  • 50-75%

    Votes: 3 1.6%
  • 75-100%

    Votes: 3 1.6%
  • 100% I’ve had enough of farming!

    Votes: 6 3.3%

Red Tractor drops launch of green farming scheme amid anger from farmers

  • 1,287
  • 1
As reported in Independent


quote: “Red Tractor has confirmed it is dropping plans to launch its green farming assurance standard in April“

read the TFF thread here: https://thefarmingforum.co.uk/index.php?threads/gfc-was-to-go-ahead-now-not-going-ahead.405234/
Top