Remote engage foot switch Trimble Ez Steer wiring diagram

Chap

Member
Does anyone know which number pins the 2 wires plug into on a 25 pin plug like photos for a foot switch to engage auto steer

D167321B-54B3-46ED-B5D7-2719F844F4E7.jpeg
113355B2-FF29-4A08-8F38-D4B7C20DB766.jpeg
 

Soon_60

Member
10 & 11

The designer of the T2 box must have a lot of future plans in their minds as so many pins are connected to circuit board. But they newer got used. Just the remote engage and sonalert are used as far as I have understood.
 
Last edited:

Chap

Member
10 & 11

The designer of the T2 box must have a lot of future plans in their minds as so many pins are connected to circuit board. But they newer got used. Just the remote engage and sonalert are used as far as I have understood.
Spot on thanks.
 

Tractor Boy

Member
Location
Suffolk
I’ve done this now. The soldering was extremely fiddly but I’ve done two leads with foot switches, one to use on the combine and one on my MF6499.
Tested them both and they both work, so all is good.
 

JeremyD

Member
Arable Farmer
What switches have you fitted? I want to fit footswitch but dont no which one to buy? All proper ones are expensive!
 
Last edited:

e3120

Member
Mixed Farmer
Location
Northumberland

Would this work?
Yeah, that's what I use on an ez pilot. Did have to drill a small hole to secure the pivot pin, as you can't access the grubscrew after screwing to the floor mat.
 

jcawley

Member
Trade
What switches have you fitted? I want to fit footswitch but dont no which one to buy? All proper ones are expensive!
The ones we get from trimble are a expensive but you can buy the one for the Autopilot that comes with just the pins on it and then you can get your own connectors.
https://agtogo.com/products/ez-pilot-pro-foot-switch-trimble-57259s?_pos=3&_sid=2a1ed5131&_ss=r $69.95 USD
The expensive part is that they usually add in an adapter cable instead of working with the manufacturer to put on a standard deutsch connection for each steering system.

As far as what switch will work, it is a standard on/off switch and you can likely make anything work as long as you get the pins correct. We sell a lot of the toggle switches because they are less expensive and a little cleaner in the cab.
 

Lofty1984

Member
Mixed Farmer
Location
South wales
If I wanted to install a switch for a pedal or normal flick switch would I need to plug it into port b port a I believe is used to the steering motor
B2E4B60E-0103-4B72-B6DB-76F6D78D13DE.png
 

JeremyD

Member
Arable Farmer
Ez steer goes into t2 control box via 25 pin plug, ez pilot connects via sonar alert on loom from memory I will have a look later if I get chance.
 

SFI - What % were you taking out of production?

  • 0 %

    Votes: 80 42.3%
  • Up to 25%

    Votes: 66 34.9%
  • 25-50%

    Votes: 30 15.9%
  • 50-75%

    Votes: 3 1.6%
  • 75-100%

    Votes: 3 1.6%
  • 100% I’ve had enough of farming!

    Votes: 7 3.7%

Red Tractor drops launch of green farming scheme amid anger from farmers

  • 1,292
  • 1
As reported in Independent


quote: “Red Tractor has confirmed it is dropping plans to launch its green farming assurance standard in April“

read the TFF thread here: https://thefarmingforum.co.uk/index.php?threads/gfc-was-to-go-ahead-now-not-going-ahead.405234/
Top