Starfire auto steer

[cla2170]

Fairly new to autosteer, got drilling today and working fine but wandered if there's any way to mark out say a 12m headland so I know where to lift drill? Drill is 4m. Thanks

 

[beefandsleep]

Yes, very easy. You have to program a constant offset to an already mapped field boundary.

 

[cla2170]

Thanks, will look into that, and also, can you have it so that it marks out the tramlines? On sf2 2600 display

 

[Northdowns Martin]

To record boundaries goes into maps, drive perimeter recording then set constant interior headland at 12m you should get a broken pink line on the screen

 

[Northdowns Martin]

Thanks, will look into that, and also, can you have it so that it marks out the tramlines? On sf2 2600 display

Once you have set your AB line it will mark out what ever distance you like between runs

 

[cla2170]

Once you have set your AB line it will mark out what ever distance you like between runs

Thanks, I'm drilling with 4m drill but wandered if it could mark out every 6th rin in different colour to mark 24m tramlines?

 

[KB6930]

What screen?

I can do tramlines on my 2630 and my 4240 but couldn't on the integrated 4600 on 6155 .

I've not figured out the inner headland line on the 2630 yet but don't really need it

 

[Northdowns Martin]

Thanks, I'm drilling with 4m drill but wandered if it could mark out every 6th rin in different colour to mark 24m tramlines?

Good point, would love it know if possible on a 2600. I strike out first tram on a 0 and every multiple of a 6 is a tramline run ie. 6,12,18

 

[KB6930]

Good point, would love it know if possible on a 2600. I strike out first tram on a 0 and every multiple of a 6 is a tramline run ie. 6,12,18

2600 too old as far as I know

 

[beefandsleep]

Thanks, I'm drilling with 4m drill but wandered if it could mark out every 6th rin in different colour to mark 24m tramlines?

Go to the guidance page, then tramline settings, you can put in how often you want a tramline adding and shift it across to the desired track. It is highlighted a different colour.

 

[Brisel]

You can mark out tramlines on the newer screens. I've never tried on a 2600 & we never bothered anyway. The drill wasn't Isobus & did its own thing. The sprayer had the normal AB lines.

 

[KB6930]

Good point, would love it know if possible on a 2600. I strike out first tram on a 0 and every multiple of a 6 is a tramline run ie. 6,12,18

You need this to do it

 

[Phil P]

Just note the OP is on a 2600 screen and I’m pretty sure you can’t highlight tramlines with a 2600 screen.
He’ll be running on gs2 software which is pretty old hat (we’re on gs4 now) and I don’t think it’s supported with updates any longer.
As for internal boundaries I honestly can’t remember if it’s possible on a 2600, best to consult the book. It will be in the boundaries section.

 

[Northdowns Martin]

Just note the OP is on a 2600 screen and I’m pretty sure you can’t highlight tramlines with a 2600 screen.
He’ll be running on gs2 software which is pretty old hat (we’re on gs4 now) and I don’t think it’s supported with updates any longer.
As for internal boundaries I honestly can’t remember if it’s possible on a 2600, best to consult the book. It will be in the boundaries section.

We use internal boundaries for drilling on 2600 screen. Looks like @KB6930 demo was using GS3 software

 

[KB6930]

We use internal boundaries for drilling on 2600 screen. Looks like @KB6930 demo was using GS3 software

I can make them but will mean driving round the field again by the looks of it which I'm not prepared to do for no good reason. The newer screens just do it automatically off the boundary

 

[Phil P]

We use internal boundaries for drilling on 2600 screen. Looks like @KB6930 demo was using GS3 software

It’s a long time since I’ve used a 2600 and I’ll be honest it was never the easiest to navigate when I did.
yes looks like KB is demoing a 2630 which will be gs3, all mine are gs4 which is a lot different to anything that has come before.

 

[Phil P]

I can make them but will mean driving round the field again by the looks of it which I'm not prepared to do for no good reason. The newer screens just do it automatically off the boundary

Thought you could put an internal boundary in on a 2630 , just put a headland offset in?

 

[Phil P]

@KB6930

https://www.deere.co.uk/common/docs/services_and_support/stellarsupport/en_R2/ag_management_solutions/displays_and_receivers/greenstar-3-display-2630/PFP13445_GS3_2630_Display_EN.pdf

 

[Will 1594]

And remember if on 24 m / 4 drill put no 5 in your tramline setting. So it highlights on 6 th run , your tramline run

 

[KB6930]

@KB6930
View attachment 948926

https://www.deere.co.uk/common/docs/services_and_support/stellarsupport/en_R2/ag_management_solutions/displays_and_receivers/greenstar-3-display-2630/PFP13445_GS3_2630_Display_EN.pdf

Been playing with it and it definitely wants me to drive round again