Today at work

Discussion in 'Pictures & Videos' started by Penmoel, May 20, 2013.

  1. Adeptandy

    Adeptandy Member

    Location:
    PE15
    Any suggestions on removing fencing, approx 7km to take out, sheep netting, barb and high tensile, posts rotten at ground level :rolleyes:
     
  2. Pan mixer

    Pan mixer Member

    Location:
    Near Colchester
    Grab or 3 in one bucket on the telescopic, bonfire, scrapyard.
     
  3. ARW

    ARW Member

    Location:
    Yorkshire
    We have a 4 in 1 for loader, big heap, big fire, then a big magnet out there f an old amplifier to pick up staples!
    Either that or pull staples out and roll up. Either way is crap
     
  4. Courier

    Courier Member

    3.5T is meant to be the Gross Weight - not the load.
     
    Nearly likes this.
  5. Adeptandy

    Adeptandy Member

    Location:
    PE15
    Van is at 3.5t gross inc load, just ignore the trailer ;) think it stopped quicker with the loaded trailer on than it does normally :D
     
    bobk, Courier and Dman2 like this.
  6. Adeptandy

    Adeptandy Member

    Location:
    PE15
    I feared it was going to be a rubbish job :(
     
  7. S J H

    S J H Member

    Location:
    Bedfordshire
    What do you do on the joints @Pan mixer , are they concreted in aswell?
     
  8. davidroberts30

    Location:
    pembrokeshire
    Do i win for being the closest :LOL:
     
  9. Mickeymatbro

    Mickeymatbro Member

  10. Mickeymatbro

    Mickeymatbro Member

    tractorbob likes this.
  11. Nearly

    Nearly Member

    Location:
    YO7
    REStracTORATION and yellowbelly like this.
  12. yellowbelly

    yellowbelly Member

    Location:
    N.Lincs
    I've always thought it was foxes but yesterday I saw a crow fly past with one sticking out it's mouth like a big cigar:cool:
     
    holwellcourtfarm likes this.
  13. Shovelhands

    Shovelhands Member

    Location:
    Sunny Essex
    Calm and peaceful start on the marshes this morning :cool: image.jpeg went and took the scaffolding down on this yesterday. Really pleased with how it's turned out... image.jpeg A vast improvement on the rotten rubbish that we started with:rolleyes: image.jpeg
     
    REStracTORATION, FE35, sherg and 13 others like this.
  14. Hi davedb, it copes OK, you can track and flail, it does sap some of the power but it does keep turning. It is a nice piece of kit though :)
     
    davedb likes this.
  15. I wish
     
  16. Pan mixer

    Pan mixer Member

    Location:
    Near Colchester
    The whole lot of the plumbing will be below a DPM, the joints all have a big shovelful or two of soft sand round them so that there is only a 2 inch thick bit of concrete above - where the joints are is under the metal-work of the drinker-holder so no direct hoof/or telescopic loader will drive near them either.

    I have dug too many joints up over the years to want to concrete in a tee.
     
    Adeptandy likes this.
  17. Pan mixer

    Pan mixer Member

    Location:
    Near Colchester
    I guessed that you were about to unlevel some more of Essex and there you go again.:)
     
    Shovelhands likes this.
  18. Pan mixer

    Pan mixer Member

    Location:
    Near Colchester
    I use one of these workshop floor magnets for that staple bit, they are very efficient as you just pull a handle and all scrap is released.

    https://www.sitebox.ltd.uk/clarke-m...MIppSv_anA1wIVFijTCh0FsgmkEAQYASABEgKN6PD_BwE
     
  19. Shovelhands

    Shovelhands Member

    Location:
    Sunny Essex
    Have no fear, it's not that level here anyway, the area is flat, but very few bits are actually 'level', I'm not destroying the precious landscape :)
    image.jpeg
     
    Adeptandy, v8willy, Pan mixer and 5 others like this.
  20. davidroberts30

    Location:
    pembrokeshire
    Mickeymatbro likes this.

Share This Page