Weld on gate hangers

[devonshire farmer]

probably been done already but where do people get the best price on weld on gate hangers, probably get a dozen if good price, mole valley are £1.50 ex vat can this be beaten?

 

[TripleSix]

https://www.sam-turner.co.uk/catalogsearch/result/?q=Weld+on

 

[the-mad-welder]

FH Brundle perhaps?

£1.50 sounds cheap enough mind!

 

[devonshire farmer]

FH Brundle perhaps?

£1.50 sounds cheap enough mind![/QUOTE
Looks like mole valley may win then

 

[Nearly]

On stuff like this it's the postage that kills it.
Pick up a full box of 10 and ask for best price.
It helps if you ask if they are available pre drilled to stop cows lifting gates off, then sigh and complain about the cost of 6mm drill bits.

Would you like to make them for £1.50?

 

[Nearly]

https://elizatinsley.co.uk

 

[Lincoln75]

probably been done already but where do people get the best price on weld on gate hangers, probably get a dozen if good price, mole valley are £1.50 ex vat can this be beaten?

By the time youve driven around trying to save £3.00 you`ll have wasted a tenner in fuel and two hours of your time.
Mail order will no doubt attract £7-£10 carriage.
I just dont get some people.

 

[Forever Fendt]

old mower blades make good washers if the eye bolt has pulled into the end of the gate

 

[devonshire farmer]

By the time youve driven around trying to save £3.00 you`ll have wasted a tenner in fuel and two hours of your time.
Mail order will no doubt attract £7-£10 carriage.
I just dont get some people.

Partly the reason for asking as we are lambing and I was hoping to mail order them rather than go to mvf but looks like I will be going after all

 

[Forever Fendt]

Partly the reason for asking as we are lambing and I was hoping to mail order them rather than go to mvf but looks like I will be going after all

Lambing, Its not even mid November a lot round here will have only just put tups in

 

[devonshire farmer]

Lambing, Its not even mid November a lot round here will have only just put tups in

Father in law puts the ram in when we start pretty much

 

[Lincoln75]

Partly the reason for asking as we are lambing and I was hoping to mail order them rather than go to mvf but looks like I will be going after all

You said you were trying to save money not time.

 

[dannewhouse]

DC Iron, I don't know price of standard 20mm ones but they are the cheapest for 25mm ones, look mega compared with 20mm! but quite a bit more £££

 

[Deutzdx3]

If you wanted a box of them we can do a box of male for 1.25 each. Same for female. Delivery would be 8.95.

 

[dannewhouse]

If you wanted a box of them we can do a box of male for 1.25 each. Same for female. Delivery would be 8.95.

do you do 25mm eye bolts for on the gates?
probably after 50 ish

 

[dannewhouse]

https://www.dciron.co.uk/gp20/
£1.25 each for 20mm weld on hinges, cant remember how much postage is but they do a deal on a lump sum, possibly free postage cant remember.

 

[Deutzdx3]

do you do 25mm eye bolts for on the gates?
probably after 50 ish

I don’t keep the 25mm ones in as they are mainly supplied for 18ft gates and larger. Which are special order. I can supply them direct from my supplier. Would have to get a price from them. Can ship direct from them.

 

[dannewhouse]

View attachment 738564

I don’t keep the 25mm ones in as they are mainly supplied for 18ft gates and larger. Which are special order. I can supply them direct from my supplier. Would have to get a price from them. Can ship direct from them.

will you price 40x 150 to suit 25mm pin, I need 44 but think I have 4+ in the "well organised" store
im putting them on 120kg diagonal barriers 15ft, just think they are better that bit stronger.

 

[Nearly]

If you wanted a box of them we can do a box of male for 1.25 each. Same for female. Delivery would be 8.95.

The essential question is 'How many in a box?'

 

[Deutzdx3]

The essential question is 'How many in a box?'

I will go count the box shortly. I think maybe 25 in a box. But will check.