Written by CPM Magazine from CPM Magazine
Download PDF
For six decades, blue tractors have been built in Basildon at a plant that’s evolved and undergone significant change to match the modern requirements of farming. CPM was invited to New Holland’s 60th birthday tour.
By Martin Rickatson...
agritechnica
biogas
carbon
cnh
development
diesel
digital
environmental
family
fuel
gas
hail
management
market
markets
methane
new holland
orchards
parts
rapid
residual
robotic
slurry
software
storage
stores
t6
t7
technology
testing
tower
training
umbilical
Hi have just got a new to me 2015 T7.200 auto command. Have got 2 warning started coming up one for wheel sensor but more worryingly it's started throwing up code 2553 which i think means low gearbox pressure. I changed all filters and still does it when I am pulling a vaderstad 3m. Have tried...
30 years ago I had a MF 690 4wd on a 21m Hardi mounted sprayer with 1000l rear and 500l front tank. Times have changed somewhat though so any advice today for a 2000l rear tank and 1500l front tank with 24m booms. When loaded the rear part would gross 3600kg and the front 1800kg with water...
My Cvx 230 is my ploughing/Trio tractor and after just 2700hrs the Michelin Mach bibs are down to 20% mainly because in life before me it dragged a 21t digger around at 35psi.
Anyways 650/75 r38
Michelin £3900
Vredstein £2700
BKT £1375
Front 600/65 r38 have similar pricing.
Am I going to be...
Anyone got any suggestions where I might find a replacement 42" by 20" solid rear rim to fit a SWB NH. The wheel studs came slack on one of ours and we have cracked it. Its an 8 stud to fit a SWB T7.190
Any NH breakers that can be suggested. I have found one on ebay, at a breaker in Cork, but...
On a 40k tractor, they mostly do more than 40k but lets assume it does 40k on the dot, if its running 650/65r38, if that was changed to 650/65r42 what would the difference in top speed be?
Have a T7050 and it has suddenly developed a loud knocking noise below the flywheel that frequency is proportional to ground speed
Its seems to be the driveshaft to the front axle immediately where it comes out the front of the gearbox
anyone have a exploded diagram of this area. Any...
We have a new Holland t7.225 with receiver and nav3 controller. It’s unlocked for Rtk but need a modem for the sim. Are there any after market modems and cables available?
Written by Justin Roberts from Agriland
Tractors powered by internal combustion have been around for for just over 120 years now, and for half of that time, they have been built at Basildon, Essex in a factory built by Ford, but now owned and operated by Case New Holland.
This is a strong...
Written by Justin Roberts from Agriland
It’s been 60 years since the tractor factory at Basildon in Essex opened and New Holland is keen to mark the event, as the company remains proud of its long and illustrious heritage.
The occasion could well have brought forth the usual long, but worthy...
Is the minimum wage now abouve “Craftsman’s” wage (if such a thing still exists).
Been looking on web but most information seems to be out of date.
Looks like after 35 years farming using hundreds of thousands of pounds worth of machinery and applying the same in fert and chemical,I can say I’m...
Hi all was leading muck with t7 auto command and every now and again would cone out of gear and flash N in the centre of dashboard. Come to a stop put handbrake on then back to drive forwards until it does it again. Any ideas? Gearbox needing calibrating?
thanks
Bit of a silly question but basically would a 6 cylinder 150 hp tractor use 50% more diesel than a 100 hp 4 cylinder both doing the same work say a 3m power harrow in same conditions. Roughly same age of tractor’s.
Valtra T255V
Advert added by: B and B Tractors
Machinery Details
Category: Tractors Farm Tractors Price: £ Condition: Excellent
Description
T255V
163hrs
Ex demo
57km/h
Powershift
Front...
How to make contact with the Dealer
Click here to read...
I’ve never been a fan for tractors. Just have a tractor big enough, surely 🤷♂️
But, I bought a mower a couple of years after the tractor and it’s fine for second cut but at times with first cut I’m maxing at 8k. Not the end of the world but out of curiosity, when at the dealer I asked what they...
Hi,
I have a 2017 T6.145 AutoCommand.
It is currently stuck in the lower of two gears and won’t drive past about 10m/h
I have a 2019 T7 AC and I know by pressing two buttons I can lock her in low range, this T6 however does not have this option to lock it and is still displaying speed to up to...
Written by CPM Magazine from CPM Magazine
Download PDF
Innovation never stands still and with focus moving towards environmentally conscious management, the drill and planter section of the machinery industry is no exception. CPM takes a look at some of the newest products and updates...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.