Where is the best place to buy the tablet from.
EbayWhere is the best place to buy the tablet from.
i want to mount my tablet using a 150mm ram mount extension.
Anyone mount there tablet successfully with a 150mm extension and a 25mm ball or do I really need the 1.5" ball. cant seem to get a 1.5" ball with a clamp for mounting onto the door handle, no problem get a 1" ball with a clamp however.
Double U-Bolt Mount 1.5" Ball 1" to 1.25" OD
Double U-Bolt Mount 1.5" Ball 0.75" to 1.25" OD - The RAM-235, double u-bolt mount, will fit rails between 0.www.ram-mount.co.uk
Coated metal.is the ram mount ball just a neoprene rubber ball, is there a bit of flex in it or is it harder rubber similar to say a metal ball
I said that
"Just a simple lightbar"
I said
Then it grew
FREE!!! ntrip caster RTK corrections were discovered
And they said I'd need section control
But no, it was an ethernet connected IMU I needed. The fields are steep, and my roll error was high
I'll stop now, I said
But no, I could use section control, even though it was just to turn off the wee sprayer at the headland
That's it, I said
But making my own base station was cheap and easy, I heard
No more, I whimpered
But wait, "can it make the neighbours jealous when my plough lifts and lowers with perfect precision?", I asked
And "will the seeder start and stop with meticulous metering?" I pondered
And "will xbee radio cover the fields where time and mobile signal forgot?" I raved
My advice is, DO NOT make it full autosteer. Stick with watching the lightbar, and correct the wheel yourself. I can only imagine how awful it must be for those poor souls who have went the "whole control hogg", and now have nothing to occupy their minds other than "what else can I make the software do?"
Thank you for listening. My name is DrDunc, and I'm an agopengps addict
View attachment 1146782
Holder is a Ram Mount Tab Titewhat type of mount is that you have there, was getting similar but was informed before I purchased it blocks off the usb port cover so not much good
Holder is a Ram Mount Tab Tite
I'll recommend it. Good grip and every port is accessible
Mount is a Ram sucker onto the windscreen, with the short version of their coupling to the tab tite. Let's me shift the tablet onto the side window out the way when it's not neededany chance of a photo of how you attached to the dash at the back, did you use ram mounts
Mount is a Ram sucker onto the windscreen, with the short version of their coupling to the tab tite. Let's me shift the tablet onto the side window out the way when it's not needed
Sorry no photos (too miserable to go back outside to the cold and dark now that the fire is lit )
Yes 3 inch suction cup. Lick the finger and wet the rubber before sticking it on. Didn't let go once last summerno issues with it falling off with the sucker ? 3" suction cup or thereabouts
View attachment 1116856
4 holes on the back for a RAM ball mount, single nut and bolt at the top to clamp the tablet in place.
Got one, my Panasonic fz-g1 seems to have a bigger battery it lasts for 12hrs, not as good a fit as I had hoped. Had to take off the rubber corners, could trim those down easily however.Holder is a Ram Mount Tab Tite
I'll recommend it. Good grip and every port is accessible
Got one, my Panasonic fz-g1 seems to have a bigger battery it lasts for 12hrs, not as good a fit as I had hoped. Had to take off the rubber corners, could trim those down easily however.
USB cover can't be opened either.
Nice tight fit and v steady.
Thats useless if usb cover cant be opened.
Any difference if the tablet is rotated 180 degrees in the holder?
This is my take on a holder for the fz-g1. The lower hooks are curved to match the way the tablet flairs out at the corners. The top catch can be flicked open by thumb when you grab the tablet single handed. All the ports completely uncovered. I'm one of those people that regularly use both can doors, so the mount arm just pushes round out of the way for access.
View attachment 1162498
View attachment 1162497
Also I side that plastic on the track rod end is a non contact WAS. The magnet is clamped on top of the TRE and the sensor floating above it in a chunky housing. Uses at 180 degree ampenol hall sensor like the one pictured bellow.
View attachment 1162499
View attachment 1162501
D
Also interested to know how it works as I’m struggling to get the RQH100030 WAS to work on a Case with a Carrero sprung front axle and can’t find a linear displacement sensor that will fit alongside the steering ram as there is not enough room between the axle and the ramDoes the WAS work well?
Seems a much easier way to mount than many, think its probably the biggest stumbling block.
You need a good WAS to have good steering!
How's your install with the linear sensor doing?Does the WAS work well?
Seems a much easier way to mount than many, think its probably the biggest stumbling block.
You need a good WAS to have good steering!